Virtual Link Trunking (VLT) | 1087Domain_1_Peer1(conf-if-range-te-0/16-17)#no shutdownNext, configure the VLT domain and VLTi on Peer 2:Domain_1_Peer2#configureDomain_1_Peer2(conf)#interface port-channel 1Domain_1_Peer2(conf-if-po-1)#channel-member TenGigabitEthernet 0/8-9Domain_1_Peer2#no shutdownDomain_1_Peer2(conf)#vlt domain 200Domain_1_Peer2(conf-vlt-domain)#peer-link port-channel 1Domain_1_Peer2(conf-vlt-domain)#back-up destination 10.16.130.12Domain_1_Peer2(conf-vlt-domain)#system-mac mac-address 00:0a:00:0a:00:0aDomain_1_Peer2(conf-vlt-domain)#unit-id 1Configure eVLT on Peer 2:Domain_1_Peer2(conf)#interface port-channel 100Domain_1_Peer2(conf-if-po-100)#switchportDomain_1_Peer2(conf-if-po-100)#vlt-peer-lag port-channel 100Domain_1_Peer2(conf-if-po-100)#no shutdownAdd links to the eVLT port-channel on Peer 2:Domain_1_Peer2(conf)#interface range tengigabitethernet 0/28 - 29Domain_1_Peer2(conf-if-range-te-0/16-17)#port-channel-protocol LACPDomain_1_Peer2(conf-if-range-te-0/16-17)#port-channel 100 mode activeDomain_1_Peer2(conf-if-range-te-0/16-17)#no shutdownIn Domain 2, configure the VLT domain and VLTi on Peer 3:Domain_2_Peer3#configureDomain_2_Peer3(conf)#interface port-channel 1Domain_2_Peer3(conf-if-po-1)#channel-member TenGigabitEthernet 0/8-9Domain_1_Peer3#no shutdownDomain_2_Peer3(conf)#vlt domain 200Domain_2_Peer3(conf-vlt-domain)#peer-link port-channel 1Domain_2_Peer3(conf-vlt-domain)#back-up destination 10.18.130.11Domain_2_Peer3(conf-vlt-domain)#system-mac mac-address 00:0b:00:0b:00:0bDomain_2_Peer3(conf-vlt-domain)#unit-id 0Configure eVLT on Peer 3:Domain_2_Peer3(conf)#interface port-channel 100Domain_2_Peer3(conf-if-po-100)#switchportDomain_2_Peer3(conf-if-po-100)#vlt-peer-lag port-channel 100Domain_2_Peer3(conf-if-po-100)#no shutdownAdd links to the eVLT port-channel on Peer 3:Domain_2_Peer3(conf)#interface range tengigabitethernet 0/19 - 20Domain_2_Peer3(conf-if-range-te-0/16-17)#port-channel-protocol LACPDomain_2_Peer3(conf-if-range-te-0/16-17)#port-channel 100 mode activeDomain_2_Peer3(conf-if-range-te-0/16-17)#no shutdownNext, configure the VLT domain and VLTi on Peer 4:Domain_2_Peer4#configureDomain_2_Peer4(conf)#interface port-channel 1Domain_2_Peer4(conf-if-po-1)#channel-member TenGigabitEthernet 0/8-9Domain_1_Peer4#no shutdown
