Denon DVD-3910 Operating Instructions Manual

Also see for DVD-3910: Supplementary guide Operating instructions Specifications Specification Operating instructions

Contents

15ENGLISHIn the stop mode, press the SETUP button.• The setup (default settings) screen appears.NOTE: For some menus, the initial values can bechanged during playback.LANGUAGE SETUPUse this to set the language to be used whenplaying the disc. If the set language is not offeredon that disc, the discs default language is set.And use this to set the language for the defaultsetting screen and messages displayed on the TVscreen (“PLAY”, etc.).DIGITAL INTERFACE SETUPUse this to set the output of DVI, HDMI, DENONLINK and IEEE1394 terminals.VIDEO SETUPUse this to set the DVD-3910’s screen mode.(TV aspect, TV type and AV1 video output.)AUDIO SETUPUse this to set the DVD-3910’s audio outputmode.(Digital and LPCM output settings.)RATINGSUse this to disable playback of adult DVDs sothat children cannot watch them. Note thatplayback of adult DVDs cannot be disabled if therating level is not recorded on the DVD, but thatit is possible to disable playback of all DVDs.OTHER SETUPThese include special settings such as CAPTIONS,WALL PAPER, etc,.#0 SLOW/SEARCH buttons#1 PAGE –/PAGE + buttons• Use these to selected the desired still pictureon DVD audio discs containing browseablestill pictures.#2 ZOOM button• Press this to enlarge the image.NOTES:• Be sure to turn on the power before opening andclosing the disc tray.• Do not strike on the button with a pencil, etc.7 LOADING DISCS2 Set discs in the disc tray with the labeled (printed)side facing up.Inner discguide(8 cm disc)Outer disc guide(12 cm disc)Disc trayNOTE:• Do not move the DVD-3910 while a disc is playing.Doing so may scratch the disc.(1) Opening and Closing the Disc Trayq Turn on the power.w Press the OPEN/CLOSE button.Disc trayPower switch OPEN/CLOSEbutton(2) Loading DiscsFigure 1Outer disc guide12 cm discFigure 2Inner disc guide8 cm discNOTES:• If a foreign object is caught in the disc tray duringclosing, simply press the OPEN/CLOSE buttonagain and the tray will open.• Do not press the disc tray in by hand when thepower is off. Doing so will damage it.• Do not place foreign objects in the disc tray.Doing so will damage it.• Pick up the disc carefully so as not to touch thesignal surface and hold it with the labeled sidefacing up.• With the disc tray fully open, set the disc in the disctray.• Set 12 cm discs in the outer disc guide (Figure 1), 8cm discs in the inner disc guide (Figure 2).• Press the OPEN/CLOSE button.The disc is automatically loaded.• The disc tray can also be closed automatically to loadthe disc by pressing the PLAY button.#3 DIMMER button• Use this to adjust the brightness of the mainunit’s display.Can be switched in 4 steps, from all off toalways on.#4 PURE DIRECT MEMORY/SELECT buttons• Use these to make and select that varioussetting to achieve higher quality sound.8 CHANGING THE DEFAULT SETTINGSON / STANDBYSOPEN/CLOSEDENON LINK AL 24 PLUS112 Make the initial settings to suit your usage conditions before starting playback.The initial settings are retained until they are next changed, evenif the power is turned off.SELECTHDMI/DVIOPEN/SUPER AUDIOFORMATNTSC/PAL CLOSECD SETUPPROGRAM/DIRECTCLEARCALLSEARCH MODEAUDIOSUBTITLEANGLEPAGEMARKERRANDOMDIMMERZOOMPICUREADJUSTSETUPMEMORYA-BREPEATSELECTRC-972PURE DIRECTDISPLAYTOP MENURETURNMENUSKIPSLOW/SEARCHPLAYSTILL/PAUSESTOPBACK LIGHTPOWER OFFPOWER ON132ON / STANDBYMain unitON / STANDBYMain unitPOWER ONRemote control unit(Red)L ANGUAGE SE TUPSE L ECT : DEC I S I ON : ENTER BUT TOND I AL OGD I SC MENUSOSD LANGUAGEE X I T SE TUPSUBT I TL EENGL I SHENGL I SHENGL I SHENGL I SH✽ To exit the setup modeUse the ª cursor button to select “EXIT SETUP”, then press the ENTER button. It is also possible to quit bypressing the SETUP button on the remote control unit.SETUPRemote control unitRemote control unit(Greeen)21Turn on the power.• Press the power button, the power indicator lightsgreen and the power turns on.When pressed again, the power turns off andindicator is off.• In the standby mode (the power indicator lightsred), press the ON/STANDBY button on the mainunit or POWER ON button on the RC-972.3Use the 0 and 1 cursor buttons to select the desiredsetting item, then press the ENTER button.Select “LANGUAGE SETUP”. (See page 17.)Select “DIGITAL INTERFACE SETUP”. (See page 18.)Select “VIDEO SETUP”. (See page 20.)Select “AUDIO SETUP”. (See page 21.)Select “RATINGS”. (See page 24.)Select “OTHER SETUP” (See page 25.)