Eaton Profile Genesys G110 Series Installation Manual Manual pdf 11 page image
Manuals database logo
manualsdatabase
Your AI-powered manual search engine

Eaton Profile Genesys G110 Series Installation Manual

Page 1 previewPage 2 previewPage 3 previewPage 4 previewPage 5 previewPage 6 previewPage 7 previewPage 8 previewPage 9 previewPage 10 previewPage 11 previewPage 12 previewPage 13 previewPage 14 previewPage 15 previewPage 16 previewPage 17 previewPage 18 previewPage 19 previewPage 20 previewPage 21 previewPage 22 previewPage 23 previewPage 24 previewPage 25 previewPage 26 previewPage 27 previewPage 28 previewPage 29 previewPage 30 previewPage 31 previewPage 32 previewPage 33 previewPage 34 previewPage 35 previewPage 36 previewPage 37 previewPage 38 previewPage 39 previewPage 40 previewPage 41 previewPage 42 previewPage 43 previewPage 44 previewPage 45 preview
Contents
  1. Table Of Contents
  2. Table Of Contents
  3. about this guide
  4. Introduction
  5. washers and grommets you will be using
  6. Installation Overview/Checklist
  7. Unpack the Box Contents
  8. Workstation Components
  9. Lifts Covered in this Manual
  10. Installing the Dual-Lift Workstation Introduction
  11. Install the Rear Lift Column Assembly
  12. Install the Front Lift Column Assembly
  13. Attach Leg Assemblies to Base
  14. Attach Leg and Base Support Covers
  15. Level Assembled Components
  16. Attach Lower Frame
  17. Attach Workstation Support
  18. Install Rear Surface and Trim Assembly
  19. Attach Center Column Cable Chains
  20. Drill Holes for Flat Panel Display Support
  21. Attach Rear Surface Trim Panels
  22. Attach Rear Surface
  23. Install User Surface and Components
  24. Attach Left Cable Chain to User Surface
  25. Attach Lift Control Box and Operator Control Pad
  26. Route Cables
  27. Install the Rear Cover
  28. Initialize the System
  29. Installation Options for the G111 Series
  30. Troubleshooting
  31. International Distribution
  32. Documentation
Eaton Profile Genesys G110 Series Installation Manual Manual pdf 11 page image
Pre-Installation Preparation and PlanningUnpack the Box ContentsBefore you begin the installation and assembly process, ensure that the following parts are includedin your shipment. Refer to the illustration on the next page for a diagram of all system componentsincluded in the PROKIT46 assembly (60” x 60” workstation). If any parts are missing, then contactTechnical Support at to.support@eaton.com.Item Part Qty Part NumberProfile Dual Genesys Lift (varies based on model) 1 See P/Ns List1 Base, Grommet 2 941742 Top, Grommet 2 941753 Screw #8-32 x 3/8” Flathead Thread Cutting 15 186184 Washer, Lock, Helical 24 189505 Screw, ¼-20x1/2 Hex Washer HD 8 543486 Hole Plug, 1.5” 1 609067 Screw, #10A x 1.00 Phillips Pan Head 49 620718 Screw, Pan Head Thread Form 38 667149 Leveler 10 6843510 Washer – 3/8” W Series 2 8278511 Screw, ¼-20 x ½” Phillips Pan Head 2 8310512 Screw M6 x 20MM Phillips Pan Head 8 8523413 AC Power Cord 3m 1 8963014 Motor Control Cable, 1000mm (39”) 2 8963115 LINAK CBD4 – 3 Lift, 120Vac 1 9006616 Motor Control Cable, 2000mm (78”) 1 9007117 Screw – M6 x 10MM Phillips Pan Head 8 9150318 LINAK, DL6 Desklift, 1200N (270 lb) 2 9624119 Motor Control, Extension Cable 1 9677920 E-Chain, 41 Links 2 9735221 E-Chain, 53 Links 1 9736222 Screw, Phillips Pan Head 10 9740823 Screw, Philip Pan Head 4 9740924 Bushing – Heyco Snap 2 9749225 Bolt, Hex Head, 3/8-16 x 2.5 2 9812926 Label – Eaton Profile 1 9813727 Top Cap Compass Foot 2 17706X28 WLD, Beam Support 1 20040X29 WLD, Base 1 20041X30 WLD, Foot, DL6 2 20107X31 WLD, Frame, User Deck 1 Varies32 WLD, Lower Frame 1 Varies33 Bracket, Cable Chain Mounting 1 20546X34 End Cap 2 1554X35 Plastic Cover 1 20756X36 Base Support Cover 1 20042X37 Flat Panel Display Deck Workstation 1 Varies38 Bracket, 17 Power Strip Mount 1 21355X39 Toe Cap – Next Generation 4 21356X40 Assembly, LINAK, DL2 1 22118X41 Plastic Cover 1 22650X42 Front Cover, Rear Surface 1 21614X43 Side Cover, Rear Surface 2 21615X44 Rear Cover, Rear Surface 1 21616X45 Cover, Leg, Right 1 Varies46 Cover, Leg, Left 1 Varies47 Attachment Bracket, Right 1 22156X48 Attachment Bracket, Left 1 22157X49 Workstation, 90-48x42x48, User Surface 1 Varies50 Screw supplied with DL2 by LINAK 8 N/Awwww.eaton.com/powerquality 11-41 06-2011 Eaton Profile Genesys Dual-Lift Ergonomic Workstation Installation 6
/ 45
Related manuals for Eaton G110 Series
Eaton TRIPP LITE WWSS1332C Manual first page preview
Eaton TRIPP LITE WWSS1332C Manual
Eaton TRIPP LITE WWSS1332W Manual first page preview
Eaton TRIPP LITE WWSS1332W Manual
Eaton CROUSE-HINDS Series Firmware Update first page preview
Eaton CROUSE-HINDS Series Firmware Update
This manual is suitable for:
G110 SeriesG111 Series
Manuals database logo
manualsdatabase
Your AI-powered manual search engine