Eaton Profile Genesys G110 Series Installation Manual Manual pdf 22 page image
Manuals database logo
manualsdatabase
Your AI-powered manual search engine

Eaton Profile Genesys G110 Series Installation Manual

Page 1 previewPage 2 previewPage 3 previewPage 4 previewPage 5 previewPage 6 previewPage 7 previewPage 8 previewPage 9 previewPage 10 previewPage 11 previewPage 12 previewPage 13 previewPage 14 previewPage 15 previewPage 16 previewPage 17 previewPage 18 previewPage 19 previewPage 20 previewPage 21 previewPage 22 previewPage 23 previewPage 24 previewPage 25 previewPage 26 previewPage 27 previewPage 28 previewPage 29 previewPage 30 previewPage 31 previewPage 32 previewPage 33 previewPage 34 previewPage 35 previewPage 36 previewPage 37 previewPage 38 previewPage 39 previewPage 40 previewPage 41 previewPage 42 previewPage 43 previewPage 44 previewPage 45 preview
Contents
  1. Table Of Contents
  2. Table Of Contents
  3. about this guide
  4. Introduction
  5. washers and grommets you will be using
  6. Installation Overview/Checklist
  7. Unpack the Box Contents
  8. Workstation Components
  9. Lifts Covered in this Manual
  10. Installing the Dual-Lift Workstation Introduction
  11. Install the Rear Lift Column Assembly
  12. Install the Front Lift Column Assembly
  13. Attach Leg Assemblies to Base
  14. Attach Leg and Base Support Covers
  15. Level Assembled Components
  16. Attach Lower Frame
  17. Attach Workstation Support
  18. Install Rear Surface and Trim Assembly
  19. Attach Center Column Cable Chains
  20. Drill Holes for Flat Panel Display Support
  21. Attach Rear Surface Trim Panels
  22. Attach Rear Surface
  23. Install User Surface and Components
  24. Attach Left Cable Chain to User Surface
  25. Attach Lift Control Box and Operator Control Pad
  26. Route Cables
  27. Install the Rear Cover
  28. Initialize the System
  29. Installation Options for the G111 Series
  30. Troubleshooting
  31. International Distribution
  32. Documentation
Eaton Profile Genesys G110 Series Installation Manual Manual pdf 22 page image
Installing the Ergonomic WorkstationAttach Lower FrameFollow these instructions and refer to the illustration below to attach the workstation support frame tothe assembled components. It is very important to perform these instructions in the sequential ordernoted here; otherwise, failure to do so may result in personal injury or product damage.CAUTION: To prevent personal injury and product damage, two or more people are required toperform the following procedure.1. From the sides of the lift column, remove the two pre-installed Phillips screws (96983) as shown inillustration below.2. On the middle front of the lift column, loosen the center pre-installed Phillips screw (96983) byapproximately 0.125 inch.IMPORTANT: Do not tighten any screws until the frame is level and aligned!Step StepStep Step (2x)Step Step (2x)Step (2x) Step (2x)3. Hook the lower frame to the column using the loosened center support Phillips screw (96983).4. At the left leg support, insert two Phillips machine screws (97409) and two lock washers (18950).Align edges square to the DL6 mounting plate.5. At the right leg support, insert two Phillips machine screws (97409) and two lock washers (18950).Align edges square to the DL6 mounting plate.6. Insert two Phillips screws (96983) through the frame into the column.17 Eaton Profile Genesys Dual-Lift Ergonomic Workstation Installation wwww.eaton.com/powerquality 11-41 06-2011
/ 45
Related manuals for Eaton G110 Series
Eaton TRIPP LITE WWSS1332C Manual first page preview
Eaton TRIPP LITE WWSS1332C Manual
Eaton TRIPP LITE WWSS1332W Manual first page preview
Eaton TRIPP LITE WWSS1332W Manual
Eaton CROUSE-HINDS Series Firmware Update first page preview
Eaton CROUSE-HINDS Series Firmware Update
This manual is suitable for:
G110 SeriesG111 Series
Manuals database logo
manualsdatabase
Your AI-powered manual search engine