Eaton Profile Genesys G110 Series Installation Manual Manual pdf 15 page image
Manuals database logo
manualsdatabase
Your AI-powered manual search engine

Eaton Profile Genesys G110 Series Installation Manual

Page 1 previewPage 2 previewPage 3 previewPage 4 previewPage 5 previewPage 6 previewPage 7 previewPage 8 previewPage 9 previewPage 10 previewPage 11 previewPage 12 previewPage 13 previewPage 14 previewPage 15 previewPage 16 previewPage 17 previewPage 18 previewPage 19 previewPage 20 previewPage 21 previewPage 22 previewPage 23 previewPage 24 previewPage 25 previewPage 26 previewPage 27 previewPage 28 previewPage 29 previewPage 30 previewPage 31 previewPage 32 previewPage 33 previewPage 34 previewPage 35 previewPage 36 previewPage 37 previewPage 38 previewPage 39 previewPage 40 previewPage 41 previewPage 42 previewPage 43 previewPage 44 previewPage 45 preview
Contents
  1. Table Of Contents
  2. Table Of Contents
  3. about this guide
  4. Introduction
  5. washers and grommets you will be using
  6. Installation Overview/Checklist
  7. Unpack the Box Contents
  8. Workstation Components
  9. Lifts Covered in this Manual
  10. Installing the Dual-Lift Workstation Introduction
  11. Install the Rear Lift Column Assembly
  12. Install the Front Lift Column Assembly
  13. Attach Leg Assemblies to Base
  14. Attach Leg and Base Support Covers
  15. Level Assembled Components
  16. Attach Lower Frame
  17. Attach Workstation Support
  18. Install Rear Surface and Trim Assembly
  19. Attach Center Column Cable Chains
  20. Drill Holes for Flat Panel Display Support
  21. Attach Rear Surface Trim Panels
  22. Attach Rear Surface
  23. Install User Surface and Components
  24. Attach Left Cable Chain to User Surface
  25. Attach Lift Control Box and Operator Control Pad
  26. Route Cables
  27. Install the Rear Cover
  28. Initialize the System
  29. Installation Options for the G111 Series
  30. Troubleshooting
  31. International Distribution
  32. Documentation
Eaton Profile Genesys G110 Series Installation Manual Manual pdf 15 page image
Installing the Ergonomic WorkstationInstall the Rear Lift Column AssemblyFollow these procedures to assemble the rear lift column assembly.Attach Lift Column to Base AssemblyFollow these instructions to attach the rear lift column to the base.NOTE: This procedure requires a team of two people to support and stabilize the lift column andbase until the fasteners are secure and the assembly is resting on the base.Raise the leveling feet on the base cover to 3/4” before you begin the assembly process.1. Turn the lift column upside down as shown in the illustration below.BaseStep (2x)Base CoverDL2Front of Lift Shown2. Remove the two screws as shown and retain for later use.3. Slide the base cover over the lift column as shown above.4. Hold the lift column in a vertical position and align the four holes on the base with theholes on the DL2 lift column. Using the four lock washers (18950) and four TORX M8x35 flatheadscrews, loosely attach the base to the lift column as shown in the following illustration.wwww.eaton.com/powerquality 11-41 06-2011 Eaton Profile Genesys Dual-Lift Ergonomic Workstation Installation 10
/ 45
Related manuals for Eaton G110 Series
Eaton TRIPP LITE WWSS1332C Manual first page preview
Eaton TRIPP LITE WWSS1332C Manual
Eaton TRIPP LITE WWSS1332W Manual first page preview
Eaton TRIPP LITE WWSS1332W Manual
Eaton CROUSE-HINDS Series Firmware Update first page preview
Eaton CROUSE-HINDS Series Firmware Update
This manual is suitable for:
G110 SeriesG111 Series
Manuals database logo
manualsdatabase
Your AI-powered manual search engine