Eaton Profile Genesys G110 Series Installation Manual Manual pdf 38 page image
Manuals database logo
manualsdatabase
Your AI-powered manual search engine

Eaton Profile Genesys G110 Series Installation Manual

Page 1 previewPage 2 previewPage 3 previewPage 4 previewPage 5 previewPage 6 previewPage 7 previewPage 8 previewPage 9 previewPage 10 previewPage 11 previewPage 12 previewPage 13 previewPage 14 previewPage 15 previewPage 16 previewPage 17 previewPage 18 previewPage 19 previewPage 20 previewPage 21 previewPage 22 previewPage 23 previewPage 24 previewPage 25 previewPage 26 previewPage 27 previewPage 28 previewPage 29 previewPage 30 previewPage 31 previewPage 32 previewPage 33 previewPage 34 previewPage 35 previewPage 36 previewPage 37 previewPage 38 previewPage 39 previewPage 40 previewPage 41 previewPage 42 previewPage 43 previewPage 44 previewPage 45 preview
Contents
  1. Table Of Contents
  2. Table Of Contents
  3. about this guide
  4. Introduction
  5. washers and grommets you will be using
  6. Installation Overview/Checklist
  7. Unpack the Box Contents
  8. Workstation Components
  9. Lifts Covered in this Manual
  10. Installing the Dual-Lift Workstation Introduction
  11. Install the Rear Lift Column Assembly
  12. Install the Front Lift Column Assembly
  13. Attach Leg Assemblies to Base
  14. Attach Leg and Base Support Covers
  15. Level Assembled Components
  16. Attach Lower Frame
  17. Attach Workstation Support
  18. Install Rear Surface and Trim Assembly
  19. Attach Center Column Cable Chains
  20. Drill Holes for Flat Panel Display Support
  21. Attach Rear Surface Trim Panels
  22. Attach Rear Surface
  23. Install User Surface and Components
  24. Attach Left Cable Chain to User Surface
  25. Attach Lift Control Box and Operator Control Pad
  26. Route Cables
  27. Install the Rear Cover
  28. Initialize the System
  29. Installation Options for the G111 Series
  30. Troubleshooting
  31. International Distribution
  32. Documentation
Eaton Profile Genesys G110 Series Installation Manual Manual pdf 38 page image
Installing the Ergonomic WorkstationInstallation Options for the G111 SeriesThis section provides instructions on installing the Eaton Profile Genesys G111-SeriesErgonomic Workstation with keyboard tray. Skip this section if you are not installing thisproduct.Attach Keyboard TrayIf you ordered the keyword tray, then follow these instructions to attach the keyboard tray tothe user surface.1. Attach the keyboard assembly below the front of the user surface by hooking the frame tothe user surface support frame.Step (5x)KeyboardAssemblyStep (4x)User Surface2. From below the work surface, insert four Phillips screws (92927) through the keyboardtray supports into the user surface support frame and tighten.3. Insert five Phillips screws (92927) horizontally through the keyboard tray bracket into thefront of the user surface support frame and tighten.4. Initialize the lift by pressing the Down Arrow button on the control pad until the lift columnlowers to the “end-stop” position.33 Eaton Profile Genesys Dual-Lift Ergonomic Workstation Installation www.eaton.com/powerquality 11-41 06-2011
/ 45
Related manuals for Eaton G110 Series
Eaton TRIPP LITE WWSS1332C Manual first page preview
Eaton TRIPP LITE WWSS1332C Manual
Eaton TRIPP LITE WWSS1332W Manual first page preview
Eaton TRIPP LITE WWSS1332W Manual
Eaton CROUSE-HINDS Series Firmware Update first page preview
Eaton CROUSE-HINDS Series Firmware Update
This manual is suitable for:
G110 SeriesG111 Series
Manuals database logo
manualsdatabase
Your AI-powered manual search engine