B-42 F60 Feeder Protection System GE MultilinB.4 MEMORY MAPPING APPENDIX BB7269 Negative Sequence Directional Overcurrent 1 Block 0 to 4294967295 --- 1 F300 0726B Negative Sequence Directional Overcurrent 1 Events 0 to 1 --- 1 F102 0 (Disabled)726C Negative Sequence Directional Overcurrent 1 Offset 0 to 250 ohms 0.01 F001 0726D Neg Seq Directional Overcurrent 1 Pos Seq Restraint 0 to 0.5 --- 0.001 F001 63726E Reserved (3 items) 0 to 1 --- 1 F001 07271 ...Repeated for Neg Seq Directional Overcurrent 2Disconnect Switch (Read/Write setting) (24 modules)74A0 Disconnect switch 1 function 0 to 1 --- 1 F102 0 (Disabled)74A1 Disconnect switch 1 name --- --- --- F206 “SW 1"74A4 Disconnect switch 1 mode 0 to 1 --- 1 F157 0 (3-Pole)74A5 Disconnect switch 1 open 0 to 4294967295 --- 1 F300 074A7 Disconnect switch 1 block open 0 to 4294967295 --- 1 F300 074A9 Disconnect switch 1 close 0 to 4294967295 --- 1 F300 074AB Disconnect switch 1 block close 0 to 4294967295 --- 1 F300 074AD Disconnect switch 1 phase A / three-pole closed 0 to 4294967295 --- 1 F300 074AF Disconnect switch 1 phase A / three-pole opened 0 to 4294967295 --- 1 F300 074B1 Disconnect switch 1 phase B closed 0 to 4294967295 --- 1 F300 074B3 Disconnect switch 1 phase B opened 0 to 4294967295 --- 1 F300 074B5 Disconnect switch 1 phase C closed 0 to 4294967295 --- 1 F300 074B7 Disconnect switch 1 phase C opened 0 to 4294967295 --- 1 F300 074B9 Disconnect switch 1 operate time 0 to 65.535 s 0.001 F001 7074BA Disconnect switch 1 alarm delay 0 to 65.535 s 0.001 F003 074BC Disconnect switch 1 events 0 to 1 --- 1 F102 0 (Disabled)74BD Reserved (2 items) --- --- --- --- ---74BF ...Repeated for module number 2Thermal Overload Protection (Read/Write Settings) (2 modules)7788 Thermal Protection 1 Function 0 to 1 --- 1 F102 0 (Disabled)7789 Thermal Protection 1 Source 0 to 5 --- 1 F167 0 (SRC 1)778A Thermal Protection 1 Base Current 0.2 to 3 pu 0.01 F001 80778B Thermal Protection 1 K Factor 1 to 1.2 --- 0.05 F001 110778C Thermal Protection 1 Trip Time Constant 0 to 1000 min. 1 F001 45778D Thermal Protection 1 Reset Time Constant 0 to 1000 min. 1 F001 45778E Thermal Protection 1 Minimum Reset Time 0 to 1000 min. 1 F001 20778F Thermal Protection 1 Reset 0 to 4294967295 --- 1 F300 07791 Thermal Protection 1 Block 0 to 4294967295 --- 1 F300 07793 Thermal Protection 1 Target 0 to 2 --- 1 F109 0 (Self-reset)7794 Thermal Protection 1 Events 0 to 1 --- 1 F102 0 (Disabled)7795 Reserved (2 items) --- --- --- F001 07797 Repeated for Thermal Protection 2Broken conductor detection (Read/Write Settings) (6 modules)77AA Broken Conductor 1 Function 0 to 1 --- 1 F102 0 (Disabled)77AB Broken Conductor 1 Source 0 to 5 --- 1 F167 0 (SRC 1)77AC Broken Conductor 1 I2/I1 Ratio 20 to 100 % 0.1 F001 20077AD Broken Conductor 1 I1 Minimum 0.05 to 1 pu 0.01 F001 1077AE Broken Conductor 1 I1 Maximum 0.05 to 5 pu 0.01 F001 15077AF Broken Conductor 1 Pickup Delay 0 to 65.535 s 0.001 F001 2000077B0 Broken Conductor 1 Block 0 to 4294967295 --- 1 F300 077B2 Broken Conductor 1 Target 0 to 2 --- 1 F109 0 (Self-reset)77B3 Broken Conductor 1 Events 0 to 1 --- 1 F102 0 (Disabled)77B4 Reserved (2 items) --- --- --- F001 077B6 ...Repeated for Broken Conductor 2Ohm Inputs (Read/Write Setting) (2 modules)77F8 Ohm Inputs 1 Function 0 to 1 --- 1 F102 0 (Disabled)77F9 Ohm Inputs 1 ID --- --- --- F205 "Ohm Ip 1 "Table B–9: MODBUS MEMORY MAP (Sheet 34 of 68)ADDR REGISTER NAME RANGE UNITS STEP FORMAT DEFAULT
