 Repeater lockoutThis function helps prevent interference to other stations byinhibiting your transmission when a signal is received. Thetransceiver has two inhibiting conditions, repeater and busy.q Push [PWR] to turn power OFF.w While pushing [SET(LOCK)], turn power ON to enter initialset mode.e Push [SET(LOCK)] several times until the “RLO” displayappears as shown below.r Rotate the tuning dial to turn the repeater lockout functionto “RP,” “BU” or OFF.• “RP”: Transmit is inhibited when the tone squelch is closed.• “BU”: Transmit is inhibited when a signal is received.t Push [PWR] to exit initial set mode. Reversed duplex modeWhen the reversed duplex mode is selected, the receive fre-quency shifts. (Transmit frequency shifts in normal duplex mode.)Each receive and transmit frequency is shown in the tablebelow with the following conditions;Input frequency : 145.30 MHzDirection : – (negative)Offset frequency : 0.6 MHzq Push [SET(LOCK] to enter set mode.w Push [SET(LOCK)] several times until the “REV” displayappears as shown below.r Rotate the tuning dial to turn the repeater lockout functionto ON or OFF.t Push [V/MHz(SCAN)] to exit set mode.Reverse duplex mode isturned ON.USING SET MODEAuto repeater function isturned OFF.Auto repeater function is ON,tone encoder is ON.While pushing [SET(LOCK)],turn power ON.USING INITIAL SET MODEReversed OFF ONRx frequency 145.30 MHz 144.70 MHzTx frequency 144.70 MHz 145.30 MHz235 REPEATER OPERATION

explicit definitions

panel description

i function display

i rear panel

i microphone keypad

using the mounting bracket

i battery connection

i antenna installation

setting a frequency

i using the keypad

i tuning step selection

i lock functions

basic operation

i audio mute function

i selecting output power

repeater operation

subaudible tones

d frequency range and offset direction

repeater lockout

i programming a memory channel

i programming a memory channel via the microphone

i transferring memory contents

i memory clearing

i memory bank selection

i memory bank setting

call channel operation

i programming a call channel

scan operation

i scan edges programming

i skip channel setting

i scan resume condition

priority watch

i priority watch operation

dtmf memory encoder

transmitting a dtmf code

i dtmf speed

pocket beep and tone squelch

tone scan

Icom IC-V8000 Instruction Manual

RECEIVER CIRCUITS

MAIN UNIT

PLL CIRCUITS

HM-133V

LOGIC BOARD

IC-V8000

quick reference guide

battery connection

antenna installation

i repeater operation

I Front panel

I Function display

I Rear panel

I Microphone (HM-133V)

I Microphone keypad

I Preparation

I Using the keypad

I Tuning step selection

I Lock functions

I Receiving

I Audio mute function

I Transmitting

I One-touch PTT function

I Accessing a repeater

I Subaudible tones

I Offset frequency

i reversed duplex mode

I Auto repeater

I General description

I Programming a memory channel

programming a memory channel via the microphone

I Transferring memory contents

memory operation

I Memory clearing

i programming channel names

I Memory bank selection

I Memory bank setting

I Transferring bank contents

I Call channel selection

I Programming a call channel

I Scan types

I Scan start/stop

I Scan edges programming

I Skip channel setting

I Scan resume condition

I Priority watch types

I Priority watch operation

I Programming a DTMF code

i transmitting a dtmf code

I DTMF speed

I Pocket beep operation

I Code programming

I Pager operation

other functions

I Initial set mode

i weather channel operation

i microphone keys

I Partial reset

I Data cloning

I Troubleshooting

i fuse replacement

I Optional unit installation

specifications and options

mode arrangement

ANI FUNCTION

Preparation

Operation

voice scrambler