Panasonic LP-M Series Operation Manual
Also see for LP-S Series: Serial Communication GuideMaintenance GuideManual
                                                                                                                                                                                                                                                                                                                    | |
Contents
|
200 Concatenated Marking SettingThe setting method for marking the character to the work whose length exceeds the marking field is described here.Reference• In case of LP-M / LP-Z series, the function of Concatenated Marking to Flying Object can not be used in combinationwith 3D setting.• For 3D marking, “Layer No.” is used for the 3D object setting, and not for the concatenated marking order.Setting MethodIf the length of the character string to be marked to a flying object exceeds the marking field, divide the characters into thelength “marking field × 2/3”, and allocate them to each marking field as shown in the figure below.1 2 3 4 5 6 7 8 9 0 A B C D E F G H I J K L M NMoving direction of flying objectMarking field × 2/3Marking startsLayer No.: 0Layer No.: 1Layer No.: 2Layer No.: 3Layer No.: 4Character Setting • Set the characters “1 to 6” to the first line.• Set the characters “7 to B” to the second line.• Set the characters “C to G” to the third line.• Set the characters “H to L” to the fourth line.• Set the characters “M and N” to the fifth line.Marking condition • Condition No. 1: Layer No. 0. Set the marking condition of “1 to 6”.• Condition No. 2: Layer No. 1. Set the marking condition of “7 to B”.• Condition No. 3: Layer No. 2. Set the marking condition of “C to G”.• Condition No. 4: Layer No. 3. Set the marking condition of “H to L”.• Condition No. 5: Layer No. 4. Set the marking condition of “M and N”.Reference• At the marking to flying object with an encoder, the marking stops for each area when the line stops and then enters thewait state of the encoder pulse input.• 16 marking fields (layer No. 0 to 15) can be used.• Specify the character setting so that the last character in the character string should match with or go over the projectionline on the marking image screen. The projection line on the marking image screen indicates × 2/3 of marking field (startingof the next marking field). (There may be the cases that the characters set outside of the guide line (the characters in theupstream of moving direction) cannot be marked during low-speed operation.)ME-LPMSZ-OP-7 |
Related manuals for Panasonic LP-S Series
This manual is suitable for:
LP-S SeriesLP-M SeriesLP-M200LP-M200-CHNLP-M200-SLP-M200-S-CHNLP-M205LP-M205-CHNLP-M205-SLP-M205-S-CHNLP-M500LP-M500-CHNLP-M500-SLP-M500-S-CHNLP-M505LP-M505-CHNLP-M505-SLP-M505-S-CHNLP-MA00LP-MA00-CHNLP-MA05LP-MA05-CHNLP-MA05-SLP-MA05-S-CHNLP-MA06LP-MA06-CHNLP-MA06-SLP-MA06-S-CHNLP-S200LP-S200-CHNLP-S200-SFLP-S202LP-S202-CHNLP-S202-SFLP-S205LP-S205-CHNLP-S205-SFLP-S500LP-S500-CHNLP-S500-SFLP-S500WLP-S500W-CHNLP-S502LP-S502-CHNLP-S502-SFLP-S505LP-S505-CHNLP-S505-SFLP-S505WLP-S505W-CHNLP-Z SeriesLP-Z130LP-Z130-CHNLP-Z250LP-Z250-CHNLP-Z256LP-Z256-CHN
manualsdatabase
Your AI-powered manual search engine