98 - ENGLISHAppendixSpecificationsModel No. PT-VW431DUPower supply AC100 V - 240 V 50 Hz/60 HzPower consumption100 V - 240 V, 4.0 A-1.6 A 365 WWhen [Standby mode] of [Setting] is set to [Eco]: 0.3 WWhen [Standby mode] of [Setting] is set to [Network]: 12.5 W(When using DIGITAL LINK: 19.7 W)When [In standby mode] of [Sound] is set to [On]: 27.5 WLCD panelPanel size 1.5 cm (0.59")(aspect ratio 16 : 10)Display method 3 transparent LCD panels (RGB)Drive method Active matrix methodPixels 1 024 000(1 280 x 800) x 3 panelsLens Manual zoom (1.6x) / Manual focus / Lens shiftF 1.6 to 2.12, f 15.28 mm to 24.62 mmLuminous lamp 280 W UHM lampLight output *1 4 300 lmContrast ratio *2 3 500 : 1 (all white / all black)Applicablescanningfrequency*3for RGB signal Horizontal 15 kHz to 100 kHz, Vertical 50 Hz to 100 HzDot clock frequency: 140 MHz or lessfor YPBPR signal[525i(480i)] Horizontal 15.75 kHz, Vertical 60 Hz[625i(576i)] Horizontal 15.63 kHz, Vertical 50 Hz[525p(480p)] Horizontal 31.50 kHz, Vertical 60 Hz[625p(576p)] Horizontal 31.25 kHz, Vertical 50 Hz[750(720)/60p] Horizontal 45.00 kHz, Vertical 60 Hz[750(720)/50p] Horizontal 37.50 kHz, Vertical 50 Hz[1125(1080)/60i] Horizontal 33.75 kHz, Vertical 60 Hz[1125(1080)/50i] Horizontal 28.13 kHz, Vertical 50 HzHD/SYNC and V terminals are not compliant with 3 value composite SYNCzfor Video signal(including S-video) Horizontal 15.75 kHz / 15.63 kHz, Vertical 60 Hz / 50 Hzfor HDMI signal525p(480p), 625p(576p), 750(720)/60p, 750(720)/50p, 1125(1080)/60i, 1125(1080)/50i,1125(1080)/24p, 1125(1080)/60p, 1125(1080)/50pDisplayable resolution: VGA to WUXGA (non-interlace)zDot clock frequency: up to 162 MHzzColor system 7 (NTSC, NTSC4.43, PAL, PAL-N, PAL-M, SECAM, PAL60)Projection size 0.76 m -7.62 m (30"-300")Screen aspect ratio 16 : 10Projection scheme Front / Rear / Mount on Ceiling / Floor (Menu setting system)Speaker 1 (4.0 cm round-type)Maximum usable volume output 10 WThese values of light output are measured under the condition that [Lamp power] is set to [Normal],*1 :[Image select] is set to [Dynamic] and [Lens Shift] is adjusted to the lowest level. Measurement, measuringconditions and method of notation all comply with ISO21118 international standards.The value of contrast ratio is measured under the condition that [Lamp power] is set to [Normal], [Image*2 :select] is set to [Dynamic], [Lens Shift] is adjusted to the lowest level and [Iris] is set to [On].For details of video signals that can be projected using this projector, refer to “List of compatible signals”.*3 :(Æpages 94-97)