Contents - trademark acknowledgements
- communication notices
- industry canada compliance statement
- german conformity statement
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Maintenance Overview
- TallyGenicom® 6600 Cartridge Ribbon Printer (CRP) Series
- How to Identify a 6600 Cartridge Ribbon Printer
- Printer Configuration Code
- Important Maintenance Notes
- About this Manual
- Printing Conventions in this Manual
- Hinweise zur Sicherheit
- Controls and Indicators
- Mechanical Controls
- Tools and Test Equipment
- Plugging in the Printer
- TallyGenicom Customer Support Center
- Corporate Offices
- Preventive Maintenance
- Cleaning the Interior
- Cleaning the Shuttle Frame Assembly
- Cleaning the Card Cage Fan Assembly
- Troubleshooting
- Start Here
- Troubleshooting Display Messages
- List of Messages
- Troubleshooting Other Symptoms
- General Symptom List
- control panel
- power failures
- power stacker
- print quality
- printer operation
- Communications Failures
- Diagnostic Printer Tests
- Selecting And Running Diagnostic Printer Tests
- Boot Diagnostics Menu
- Factory Menu
- Exception Menu
- Firmware Diagnostic Port
- Capturing Information
- Hex Code Printout
- ASCII Character Set
- Hard Reset (Cycle Power)
- Adjustments and Tests
- Preparing the Printer for Maintenance
- Returning the Printer to Normal Operation
- Belt, Paper Feed Timing, Adjustment
- Belt, Platen Open, Adjustment
- Paper Scale Alignment
- Platen Gap Adjustment
- Paper Out Adjustment
- Hammer Phasing Adjustment
- Loading Flash Memory
- Loading Software with the Firmware Download Utility
- Loading through Parallel Port using DOS
- Loading Software if Flash Contains Only Boot Code
- Loading Software through the NIC
- Reprogramming the Security Key
- Coil Temperature Adjustment
- Dynamic Paper Tension Adjustment
- Tractor Belt Tension Adjustment
- Shuttle Electrical Short Check
- Hammer Bank Power Cable Shorts Test
- Cable Shorts Test
- Main Wire Harness Test Diagnostic
- Power Supply Operational Check
- Replacement Procedures
- Belt, Paper Feed Timing
- Belt, Platen Open
- Cartridge Interface Board (CIB)
- Circuit Breaker
- Connector Coupling Shrouds
- Control Panel Assembly
- Controller Board
- Cover Assembly, Hammer Bank / Ribbon Mask
- Cover Assembly, Shuttle
- Cover Assembly, Top, Pedestal Models
- Dashpot
- Fan Assembly, Cabinet Exhaust
- Fan Assembly, Card Cage
- Fan Assembly, Hammer Bank
- Hammer Spring Assembly, Version 1
- Hammer Spring Assembly, Version 2
- Magnetic Pickup (MPU) Assembly
- Memory (Flash, Expansion)
- Motor Bracket Assembly
- Paper Feed Motor
- Paper Ironer
- Paper Guide Assembly
- Platen
- Platen Open Motor
- Platen Stop Assembly
- Power Supply Board
- Resistors, Terminating, V6 Controller Board
- Ribbon Drive Motor
- Security Key
- Shaft, Splined
- Shaft, Support
- Shuttle Frame Assembly
- Spring, Extension, Hammer Bank
- Switch Assembly, Paper Detector
- Switch Assembly, Platen Interlock
- Tractor (L/R)
- Illustrated Parts Breakdown
- Principles Of Operation
- Printing Rates
- Hammer Bank Assembly
- Shuttle Drive Motor
- Paper Transport System
- Ribbon Transport System
- Integrated Print Management System
- Logical Control of the Printer
- Control Panel
- Data Controller
- Engine Controller
- AC Power
- Printer Interface
- a wire data
- interconnection diagram
- B Abbreviations
- C Metric Conversion Tables
- mass and density
- Contents
- Introduction
- Stacker Problems
- Stacker Confidence Check
- Stacker Motor Check
- Removing the Power Stacker
- Installing the Power Stacker
- Replacing the Constant Force Spring
- Replacing the Timing Belts
- Replacing the Roller Drive Shaft
- List of Illustrations
- Overview
- Operation
- Remove Paper
- Adjust The Paper Guides
- Position the Paper Out Sensor
- Set the Tear Bar Distance
- set the top of form
- Control Panel Menus
- Performance Limitations
- paper jams
- List of Adjustments and Tests Procedures
- Preparing the ZTP Printer for Maintenance
- Barrier Panel
- Paper Guide Leaf, Front, Center, Outer
- List of Removal / Installation Procedures
- Paper Guide Leaf, Center
- Paper Out Sensor
- Tractor Assembly Support Gate
- Illustrated Parts Lists
- General Paper Specifications
- Paper Guidelines
- Environmental Considerations
- Methods of Forms Attachment
- Chaff Content
- Form Design Checklist
- Summary
- TallyGenicom Supplies Department
|
Table of ContentsShuttle Frame Assembly ................................................................ 239Spring, Extension, Hammer Bank .................................................. 241Switch Assembly, Paper Detector.................................................. 242Switch Assembly, Platen Interlock ................................................. 243Tractor (L/R)................................................................................... 244Weld Sensor................................................................................... 2446 Illustrated Parts Breakdown ................................ 245Organization of this Chapter ................................................................. 245Illustrations of Printer Components ................................................2457 Principles Of Operation....................................... 279Line Matrix Printing ............................................................................... 279Printing Rates .......................................................................................282Printing Mechanism .............................................................................. 282Shuttle Frame Assembly....................................................................... 283Hammer Bank Assembly................................................................ 283Shuttle Drive Motor ........................................................................ 284Paper Transport System....................................................................... 285Ribbon Transport System ..................................................................... 286Integrated Print Management System .................................................. 287Operation .......................................................................................287Logical Control of the Printer ................................................................ 290Control Panel ........................................................................................ 291Controller Board.................................................................................... 292Data Controller ............................................................................... 294Engine Controller ........................................................................... 296Power Supply Board ............................................................................. 298AC Power .......................................................................................298DC Power.......................................................................................298Printer Interface .................................................................................... 299A Wire Data ........................................................... 301B Abbreviations...................................................... 343C Metric Conversion Tables .................................. 351
|
