Contents - trademark acknowledgements
- communication notices
- industry canada compliance statement
- german conformity statement
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Maintenance Overview
- TallyGenicom® 6600 Cartridge Ribbon Printer (CRP) Series
- How to Identify a 6600 Cartridge Ribbon Printer
- Printer Configuration Code
- Important Maintenance Notes
- About this Manual
- Printing Conventions in this Manual
- Hinweise zur Sicherheit
- Controls and Indicators
- Mechanical Controls
- Tools and Test Equipment
- Plugging in the Printer
- TallyGenicom Customer Support Center
- Corporate Offices
- Preventive Maintenance
- Cleaning the Interior
- Cleaning the Shuttle Frame Assembly
- Cleaning the Card Cage Fan Assembly
- Troubleshooting
- Start Here
- Troubleshooting Display Messages
- List of Messages
- Troubleshooting Other Symptoms
- General Symptom List
- control panel
- power failures
- power stacker
- print quality
- printer operation
- Communications Failures
- Diagnostic Printer Tests
- Selecting And Running Diagnostic Printer Tests
- Boot Diagnostics Menu
- Factory Menu
- Exception Menu
- Firmware Diagnostic Port
- Capturing Information
- Hex Code Printout
- ASCII Character Set
- Hard Reset (Cycle Power)
- Adjustments and Tests
- Preparing the Printer for Maintenance
- Returning the Printer to Normal Operation
- Belt, Paper Feed Timing, Adjustment
- Belt, Platen Open, Adjustment
- Paper Scale Alignment
- Platen Gap Adjustment
- Paper Out Adjustment
- Hammer Phasing Adjustment
- Loading Flash Memory
- Loading Software with the Firmware Download Utility
- Loading through Parallel Port using DOS
- Loading Software if Flash Contains Only Boot Code
- Loading Software through the NIC
- Reprogramming the Security Key
- Coil Temperature Adjustment
- Dynamic Paper Tension Adjustment
- Tractor Belt Tension Adjustment
- Shuttle Electrical Short Check
- Hammer Bank Power Cable Shorts Test
- Cable Shorts Test
- Main Wire Harness Test Diagnostic
- Power Supply Operational Check
- Replacement Procedures
- Belt, Paper Feed Timing
- Belt, Platen Open
- Cartridge Interface Board (CIB)
- Circuit Breaker
- Connector Coupling Shrouds
- Control Panel Assembly
- Controller Board
- Cover Assembly, Hammer Bank / Ribbon Mask
- Cover Assembly, Shuttle
- Cover Assembly, Top, Pedestal Models
- Dashpot
- Fan Assembly, Cabinet Exhaust
- Fan Assembly, Card Cage
- Fan Assembly, Hammer Bank
- Hammer Spring Assembly, Version 1
- Hammer Spring Assembly, Version 2
- Magnetic Pickup (MPU) Assembly
- Memory (Flash, Expansion)
- Motor Bracket Assembly
- Paper Feed Motor
- Paper Ironer
- Paper Guide Assembly
- Platen
- Platen Open Motor
- Platen Stop Assembly
- Power Supply Board
- Resistors, Terminating, V6 Controller Board
- Ribbon Drive Motor
- Security Key
- Shaft, Splined
- Shaft, Support
- Shuttle Frame Assembly
- Spring, Extension, Hammer Bank
- Switch Assembly, Paper Detector
- Switch Assembly, Platen Interlock
- Tractor (L/R)
- Illustrated Parts Breakdown
- Principles Of Operation
- Printing Rates
- Hammer Bank Assembly
- Shuttle Drive Motor
- Paper Transport System
- Ribbon Transport System
- Integrated Print Management System
- Logical Control of the Printer
- Control Panel
- Data Controller
- Engine Controller
- AC Power
- Printer Interface
- a wire data
- interconnection diagram
- B Abbreviations
- C Metric Conversion Tables
- mass and density
- Contents
- Introduction
- Stacker Problems
- Stacker Confidence Check
- Stacker Motor Check
- Removing the Power Stacker
- Installing the Power Stacker
- Replacing the Constant Force Spring
- Replacing the Timing Belts
- Replacing the Roller Drive Shaft
- List of Illustrations
- Overview
- Operation
- Remove Paper
- Adjust The Paper Guides
- Position the Paper Out Sensor
- Set the Tear Bar Distance
- set the top of form
- Control Panel Menus
- Performance Limitations
- paper jams
- List of Adjustments and Tests Procedures
- Preparing the ZTP Printer for Maintenance
- Barrier Panel
- Paper Guide Leaf, Front, Center, Outer
- List of Removal / Installation Procedures
- Paper Guide Leaf, Center
- Paper Out Sensor
- Tractor Assembly Support Gate
- Illustrated Parts Lists
- General Paper Specifications
- Paper Guidelines
- Environmental Considerations
- Methods of Forms Attachment
- Chaff Content
- Form Design Checklist
- Summary
- TallyGenicom Supplies Department
|
433 TroubleshootingIntroductionThis chapter lists fault messages and general symptoms, and providesprocedures for troubleshooting printer malfunctions.NOTE: Because you must operate the printer to check its performance andsometimes you may have to reconfigure it, always have the User’sManual handy when you troubleshoot. This manual does not coverprinter operation or configuration.Troubleshooting AidsTroubleshooting is faster and more effective if you understand the equipmentand make use of all available tools.This manual has a number of troubleshooting aids to help you isolate printermalfunctions:• “Start Here” Logic Tree ............................................................... page 44• Troubleshooting Display Messages............................................ page 45• Message List............................................................................... page 46• Troubleshooting Other Symptoms ............................................ page 111• General Symptom List .............................................................. page 112• Communications Failures ......................................................... page 134• Diagnostic Printer Tests............................................................ page 136• Boot Diagnostics Menu............................................................. page 141• Factory Menu............................................................................ page 144• Exception Menu ........................................................................ page 146• Hex Code Printout .................................................................... page 149• ASCII Character Set ................................................................. page 151• Appendix A: Wire Data ............................................................. page 301
|
