Tascam DP-32SD Owner's Manual

Also see for DP-32SD: Troubleshooting supplement Schematic diagram

Contents

TASCAM DP-32SD 193 – Names and Functions of Partsg JOG/DATA dialWhen the Home screen is open, you can use this dial fortransport jog operations. (See “Cueing with the JOG/DATAdial” on page 43.)Use this dial to change parameter values and select itemswhen using menus.h ASSIGN button/indicatorUse this button to set the track type for tracks 9/10–31/32and set (assign) the input (INPUT A to H) for each track.When you press this button, the Assign screen opens. Theinput signal of the assigned input source becomes therecording source. (See “Assigning inputs” on page 33.)j MIXER button/indicatorPress to open the Mixer screen.On this screen, you can adjust the settings for the selectedinput (INPUT A to H) or track (including GROUP) that isselected. (See “Bouncing tracks” on page 41.)k DYNAMICS button/indicatorPressing this button opens a screen to adjust the settingsfor the effects applied to the inputs (INPUT A to H). (See“Dynamic effects” on page 52.)l EFFECT button/indicatorPressing this button opens a screen to make adjustmentsto the effects. (See “Guitar effects” on page 52 and “Sendeffects” on page 53.); MENU buttonPress to open the MENU screen. (See “Menu structure” onpage 22.)z HOME buttonPress to open the Home screen. (See “Home screen” on page21.)x F1 to F4 (function) buttonsThe functions of these buttons depend on the currentlyopen screen. The functions currently assigned to the F1 toF4 buttons are shown at the bottom of the screen.c PAN knobUse this knob to adjust the stereo position of the track'splayback signal or the input signal assigned to that track. (See“Stereo position (panning)” on page 54.)v SEND EFF 1/EFF 2 knobsUse these knobs to adjust the amount of track signal outputto the EFFECT SENDS jacks.Use the SEND EFF 1 knob also to adjust the amount of tracksignal sent to the internal effects. (See “Sending signals tointernal/external effects” on page 36.)b SEND MASTER 1/MASTER 2 knobsUse these knobs to adjust the amount of master track signaloutput to the EFFECT SENDS jacks.Use the SEND MASTER 1 knob also to adjust the amount ofmaster track signal sent to the internal effects. (See “Sendingsignals to internal/external effects” on page 36.)n CURSOR (5/b/g/t) buttonsUse these buttons to move the cursor on the screen.m JOG PLAY buttonPress to switch to Search mode.Operation buttons, SOLO button/indicatorPress to switch to Solo mode (the button lights). (See “Solo”on page 37.). MUTE button/indicatorPress to switch to Mute mode (the button lights). (See“Muting tracks” on page 37.)/ TRACK EDIT buttonPress to open the TRACK EDIT screen. (See “Overview oftrack editing” on page 48.)! VIRTUAL TRACK button/indicatorPress to open the VIRTUAL TRACK screen. (See “Virtualtracks” on page 47.)@ BOUNCE button/indicatorPress to switch to Bounce recording mode (the buttonlights). (See “Bouncing tracks” on page 41.)# MIXDOWN/MASTERING button/indicatorPress to cycle through the Multi Track, Mixdown andMastering modes. Mastering mode is only availablewhen there is a master track. (See “Mixing down tracks” onpage 54, “Creating a master file” on page 55, “Checkingthe master file” on page 56 and “Using the mastering tools”on page 56.)NOTEThe current mode is shown on the Home screen.$ METRONOME button/indicatorPress to set the metronome.The button flashes in time with the set tempo. (See“Metronome” on page 59.)% UNDO/REDO button/indicatorPress to undo the immediately previous action (singleundo) or to cancel the last undo (redo). (See “Undoing anoperation” on page 39.)After a single or multiple undo, the UNDO/REDO buttonlights, showing that an operation has been undone.^ MONITOR SELECT buttonPress to open the MONITOR SELECT pop-up window onthe Home screen. (See “Monitor selection” on page 34.)& MONITOR LEVEL knobUse this knob to adjust the level of the signals output fromthe MONITOR OUT jacks.* MARK SET buttonDuring recording or playback, press to set a mark manually.(See “Setting a location mark” on page 43.)