Page 114 FT DX 1200 O PERATING M ANUAL025 NUMBER STYLEFunction Selects the Contest 1umber “Cut” format foran imbedded contest number.$v a i l a b l e Va l u e s 1 0 $ U 1 2 $ U 1 T $ 1 2 $1T11211T'efault Setting 1010 'oes not abbreviate the Contest 1umber$U12 $bbreviates to “$” for “2ne”, “U” for “Two”,“1” for “1ine”, and “2” for “Zero”.$U1T $bbreviates to “$” for “2ne”, “U” for “Two”,“1” for “1ine”, and “T” for “Zero”.$12 $bbreviates to “$” for “2ne”, “1” for “1ine”,and “2” for “Zero”.$1T $bbreviates to “$” for “2ne”, “1” for “1ine”,and “T” for “Zero”.112 $bbreviates to “1” for “1ine”, and “2” for“Zero”.11T $bbreviates to “1” for “1ine”, and “T” for“Zero”.026 CONTEST NUMBERFunction (nters the initial contest number that willincrementdecrement after sending during contest QS2s.$vailable Values 0 a 'efault Setting 1027 CW MEMORY 1Function 3ermits entry of the CW message for messageregister 1.$vailable Values T(;T0(SS$G('efault Setting 0(SS$G(T(;T You may enter the CW message from theFH-.0(SS$G( You may enter the CW message from theCW keyer.028 CW MEMORY 2Function 3ermits entry of the CW message for messageregister .$vailable Values T(;T0(SS$G('efault Setting 0(SS$G(T(;T You may enter the CW message from theFH-.0(SS$G( You may enter the CW message from theCW keyer.029 CW MEMORY 3Function 3ermits entry of the CW message for messageregister 3.$vailable Values T(;T0(SS$G('efault Setting 0(SS$G(T(;T You may enter the CW message from theFH-.0(SS$G( You may enter the CW message from theCW keyer.030 CW MEMORY 4Function 3ermits entry of the CW message for messageregister 4.$vailable Values T(;T0(SS$G('efault Setting T(;TT(;T You may enter the CW message from theFH-.0(SS$G( You may enter the CW message from theCW keyer.031 CW MEMORY 5Function 3ermits entry of the CW message for messageregister .$vailable Values T(;T0(SS$G('efault Setting T(;TT(;T You may enter the CW message from theFH-.0(SS$G( You may enter the CW message from theCW keyer.GENERAL G ROUP032 ANT SELECTFunction Sets the method of antenna selection.$vailable Values B$1'ST$C.'efault Setting B$1'B$1' The antenna is selected in accordance with theoperating band.ST$C. The antenna is selected in accordance with theband stack different antennas may be utili]edon the same band, if so selected in the bandstack).033 ANT2 SETTINGFunction Selects the operation mode of the $1T connector.$vailable Values T5; 51'efault Setting T5;T5; $1T used for T; and 5;51 $1T used for 5; only034 NB LEVELFunction $djusts the noise blanking level of the IF1oise Blanker for short duration pulse noise.$vailable Values 0 a 100'efault Setting 0035 BEEP LEVELFunction Sets the beep level.$vailable Values 0 a 100'efault Setting 0036 MONITOR LEVELFunction Sets the 0onitor level.$vailable Values 0 a 100'efault Setting 0M ENU M ODE