ZIEHL-ABEGG ZETADYN 3BF manuals
ZETADYN 3BF
Table of contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- General information
- Copyright
- Product safety
- Modifications / interventions in the device
- Product overview
- Storage duration
- Dimensions / minimum clearances
- Electrical installation
- Cables motor / brake resistor
- Contacting the shielding on the frequency converter
- Contacting the shielding on the brake resistor
- Device set-up / Position of connection terminals
- Wiring
- Movable EMC cable screw glands
- Mains connection (X1)
- Line reactor-radio interference filter
- Control transformer in the mains feed line
- Connection
- Motor temperature monitoring (X-MT)
- Brake resistor (X 2)
- Digital inputs (X-IN)
- Connection with external power supply
- Technical data
- Binary traveling speed default
- Connection PWM
- DCP / CAN interface (X-DCP, X-CAN)
- Power feedback unit connection
- Technical data X-ENC8, X-ENC9 and X-ENC15
- Encoder connection synchronous motors (X-ENC15)
- Pin assignment X-ENC15 for absolute value encoder with EnDat/SSI interface
- Artificial encoder (X-ENCO)
- Connection X-EXT
- Technical data motor contactors
- External monitoring of the motor contactors (X-K)
- Assignment connection terminal X-K without integrated brake contactors
- Connection X-BR
- Integrated brake contactors (optional)
- Technical data brake contactors
- Assignment of terminals X3 and X-K in integrated brake actuation
- Connection suggestion ZETADYN 3CA (asynchronous motor)
- Connection suggestion ZETADYN 3CS (synchronous motor)
- Accessories
- Operation and parameterising
- Control key functions
- Meaning of the arrows appearing in the display
- Start-up
- Switching on the frequency inverter
- Automatic operating-curves default
- Setting the switch-off points
- Carrying out the first test run
- Serial communication
- Configuring in DCP mode
- CANopenLift
- Electrical connection
- Command- and Statusbits of the recorder
- Parameter
- Parameter list
- Advanced-Level
- Motor name plate menu
- Encoder & BC menu
- Installation menu
- Control system menu
- Monitoring menu
- Start menu
- Acceleration menu
- Decelerating menu
- Stop menu
- Parameter set 2 menu
- Statistic menu
- Memory Card menu
- MMC-Recorder menue
- Encoder adjustment menu
- Safety gear menu
- Power section menu
- ZA-Intern menu
- INFO menu
- Travel options
- Optimizing start up behavior
- Damping the start-up jerk
- Optimizing the acceleration
- Traveling speed defaults
- Normal stop during path dependent deceleration
- Arch travel with path-dependent deceleration
- Time-dependent deceleration
- Deceleration when traveling speed has not been reached
- Optimizing deceleration
- Crawl path optimization
- Optimizing stopping
- Optimizing the step alignment
- Direct leveling
- Readjustment
- Fast-start
- Monitoring functions for Quickstart
- Emergency evacuation
- Parameterisation
- Evacuation with UPS
- Evacuation through UPS with minimum power
- Improving the positioning
- Connection diagram for UPS to ZETADYN 3
- Emergency evacuation by opening the brakes
- Error diagnosis
- Software update
- Delete error memory
- Error list
- Error 1xx
- Error 3xx
- Error 4xx
- Error 5xx
- Error 7xx
- Error 9xx
- Information texts
- Operating conditions of the inverter
- Frequent startup problems
- Energy saving
- Power Feedback Unit (PFU)
- Electrical connection stand-by mode
- Special functions
- Load-free alignment SSI-Encoder
- Load-free alignment EnDat-Encoder
- Checking the load-free alignment of the SSI- & EnDat-encoders
- Rotary encoder calibration with closed brake
- Alignment absolute encoder type ERN1387
- Error messages during encoder offset alignment
- Safety Brake
- Reset
- Memory card
- Software update without the ZETAPAD operating terminal
- Error flash code during a software update
- Loading parameters
- Performing measurements
- Loading configurations
- Checking the motor phases
- Encoder-less operation (Open-Loop)
- Parameter for Open-Loop-operation
- Functions with Open-Loop-operation
- Slip-compensation
- Tilting protection
- Operation with a 3-phase 230 VAC power supply
- Controlled emergency stop in inclined elevators
- Travel direction counter
- Output functions
- Activation of the ZETADYN lock in case of a malfunctioning brake circuit
- Enclosure
- ZETADYN 3C040 - 074
- EU declaration of conformity
- Adjustment card
- Brake resistor allocation
- Type designation
- Part no
- Certificates
- Index
manualsdatabase
Your AI-powered manual search engine