GE C70 Instruction Manual

Also see for C70: Communications manual Communications guide Instruction manual Instruction manual Instruction manual

Contents

5-134 C70 CAPACITOR BANK PROTECTION AND CONTROL SYSTEM – INSTRUCTION MANUALFLEXLOGIC CHAPTER 5: SETTINGS5The following table lists alphabetically the operands available for the relay.Table 5-17: C70 FlexLogic operandsRxGOOSE Boolean On RxGOOSE Boolean 1 On The RxGOOSE Boolean is presently in the ON stateVirtual Input On Virt Ip 1 On The virtual input is presently in the ON stateVirtual Output On Virt Op 1 On The virtual output is presently in the set state (that is,evaluation of the equation that produces this virtual outputresults in a "1")Operand type Operand syntax Operand descriptionCONTROLPUSHBUTTONSCONTROL PUSHBTN 1 ONCONTROL PUSHBTN 2 ONCONTROL PUSHBTN 3 ONCONTROL PUSHBTN 4 ONCONTROL PUSHBTN 5 ONCONTROL PUSHBTN 6 ONCONTROL PUSHBTN 7 ONControl pushbutton 1 is being pressedControl pushbutton 2 is being pressedControl pushbutton 3 is being pressedControl pushbutton 4 is being pressedControl pushbutton 5 is being pressedControl pushbutton 6 is being pressedControl pushbutton 7 is being pressedCYBERSENTRY ROLE ADMIN ACTROLE SUPERVISOR ACTROLE ENGINEER ACTROLE OPERATOR ACTROLE OBSERVER ACTROLE EXTERNAL ACTAUTHENTICATION FAILUNAUTH FW ATTEMPTUNAUTH SETTING WRITERADIUS SRV UNAVAILABLEACCT SRV UNAVAILABLEAdministrator role is active and is set to true when that is the caseSupervisor role is active and is set to true when that is the caseEngineer role is active and is set to true when that is the caseOperator role is active and is set to true when that is the caseObserver role is active and is set to true when that is the caseExternal role is active and is set to true when that is the caseOperand set for Failed Authentication self-test and alarmOperand set for firmware lock self-test and alarmOperand set for settings lock self-test and alarmOperand set for RADIUS servers unavailable self-testOperand set for ACCOUNTING servers unavailable self-testDIRECT DEVICES DIRECT DEVICE 1On↓DIRECT DEVICE 16OnDIRECT DEVICE 1Off↓DIRECT DEVICE 16OffFlag is set, logic=1↓Flag is set, logic=1Flag is set, logic=1↓Flag is set, logic=1DIRECT INPUT/OUTPUT CHANNELMONITORINGDIR IO CH1 CRC ALARMDIR IO CH2 CRC ALARMDIR IO CH1 UNRET ALMDIR IO CH2 UNRET ALMThe rate of direct input messages received on channel 1 and failing the CRCexceeded the user-specified levelThe rate of direct input messages received on channel 2 and failing the CRCexceeded the user-specified levelThe rate of returned direct input/output messages on channel 1 exceededthe user-specified level (ring configurations only)The rate of returned direct input/output messages on channel 2 exceededthe user-specified level (ring configurations only)ELEMENT:Auxiliary overvoltageAUX OV1 PKPAUX OV1 DPOAUX OV1 OPAuxiliary overvoltage element has picked upAuxiliary overvoltage element has dropped outAuxiliary overvoltage element has operatedAUX OV2 to 3 Same set of operands as shown for AUX OV1ELEMENT: Automaticvoltage regulatorAVR 1 CLOSE PKPAVR 1 CLOSE OPAVR 1 CLOSE DPOAVR 1 OPEN PKPAVR 1 OPEN OPAVR 1 OPEN DPOAutomatic voltage regulator 1 picked up; close command pendingAutomatic voltage regulator 1 issued a close commandClose command of automatic voltage regulator 1 dropped outAutomatic voltage regulator 1 picked up; open command pendingAutomatic voltage regulator 1 issued an open commandOpen command of automatic voltage regulator 1 dropped outAVR 2 to 3 Same set of operands as shown for AVR 1Operand type State Example of format Characteristics[Input Is ‘1’ (= ON) if...]