GE G30 Instruction Manual
Also see for G30: Communications manualCommunications guideInstruction manualInstruction manualInstruction manual
                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                        | |
Contents
|
iv G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUALTABLE OF CONTENTS3.2.3 Rear terminal layout......................................................................................................... 3-113.3 Wiring .....................................................................................................................3-133.3.1 Typical wiring ....................................................................................................................... 3-133.3.2 Dielectric strength ............................................................................................................. 3-153.3.3 Control power ...................................................................................................................... 3-163.3.4 CT/VT modules .................................................................................................................... 3-173.3.5 Process bus modules ....................................................................................................... 3-193.3.6 Contact inputs and outputs .......................................................................................... 3-193.3.7 Transducer inputs and outputs................................................................................... 3-313.3.8 RS232 port............................................................................................................................. 3-333.3.9 CPU communication ports ............................................................................................ 3-343.3.10 IRIG-B....................................................................................................................................... 3-363.4 Direct input and output communications .......................................................3-373.4.1 Description ............................................................................................................................ 3-373.4.2 Fiber: LED and ELED transmitters............................................................................... 3-393.4.3 Fiber laser transmitters................................................................................................... 3-393.4.4 G.703 interface.................................................................................................................... 3-403.4.5 RS422 interface................................................................................................................... 3-443.4.6 RS422 and fiber interface .............................................................................................. 3-463.4.7 G.703 and fiber interface................................................................................................ 3-473.4.8 IEEE C37.94 interface ....................................................................................................... 3-473.4.9 C37.94SM interface........................................................................................................... 3-503.5 Activate relay ........................................................................................................3-533.6 Install software .....................................................................................................3-543.6.1 EnerVista communication overview ......................................................................... 3-543.6.2 System requirements....................................................................................................... 3-553.6.3 Install software.................................................................................................................... 3-563.7 Add device to software........................................................................................3-573.7.1 Set IP address in UR.......................................................................................................... 3-583.7.2 Configure serial connection.......................................................................................... 3-633.7.3 Configure Ethernet connection ................................................................................... 3-653.7.4 Configure modem connection.....................................................................................3-663.7.5 Automatic discovery of UR devices........................................................................... 3-663.8 Connect to the G30...............................................................................................3-673.8.1 Connect to the G30 in EnerVista................................................................................. 3-673.8.2 Use Quick Connect via front RS232 port................................................................. 3-683.8.3 Use Quick Connect via front USB port ..................................................................... 3-693.8.4 Use Quick Connect via a rear Ethernet port.......................................................... 3-693.9 Set up CyberSentry and change default password........................................3-703.10 Import settings .....................................................................................................3-713.11 Connect to D400 gateway...................................................................................3-723.11.1 Oscillography files.............................................................................................................. 3-723.11.2 Event records....................................................................................................................... 3-723.11.3 Log files................................................................................................................................... 3-723.11.4 Setting files............................................................................................................................ 3-734 INTERFACES 4.1 EnerVista software interface................................................................................4-14.1.1 Introduction .............................................................................................................................4-14.1.2 Settings files ............................................................................................................................4-14.1.3 Event viewing..........................................................................................................................4-24.1.4 File support ..............................................................................................................................4-34.1.5 EnerVista main window .....................................................................................................4-34.1.6 Protection summary window..........................................................................................4-44.1.7 Settings templates................................................................................................................4-54.1.8 Secure and lock FlexLogic equations ..........................................................................4-9 |
Related manuals for GE G30
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine