Jenn-Air JENN-AIR Use And Care Manual

Also see for DUAL-FUEL DOUBLE OVEN RANGE: Use & care guide

UpperCancelClock8O VEN C OOKINGTo cancel the Clock display:If you do not want the time of day to display:Press and hold the Upper Cancel and Clockpads for three seconds. The time of day willdisappear from the display.When the clock display is canceled, press the Clock pad tobriefly display the time of day.To restore the Clock display:Press and hold the Upper Cancel and Clock pads for threeseconds. The time of day will reappear in the display.TimerEach timer can be set from one minute (00:01) up to 99 hoursand 59 minutes (99:59).The timers can be used independently of any other ovenactivity. They can also be set while another oven function isoperating.The Timers do not control the oven.To set the Timer 1 or 2:1. Press the Timer 1 or 2 pad.• 00:00 and TIMER 1 or 2 flash in the display.2. Press the appropriate number pads until the correct timeappears in the display.• TIMER 1 or TIMER 2 will be displayed. If both timers areactive, TIMER 1 and TIMER 2 will be displayed.• The colon and TIMER 1 and/or 2 will continue to flash.3. Press Timer pad again or wait four seconds.• The colon stops flashing and the time begins countingdown.• The last minute of the timer countdown will be displayedin seconds.4. At the end of the set time, one long beep will sound and“End” will be displayed.5. Press the Timer pad to clear the display.To cancel the Timer:1. Press and hold the corresponding Timer padfor three seconds.OR2. Press the Timer pad and press ‘0’ using thenumber pads.Locking the Controland Oven DoorsThe touchpad and oven doors can be locked for safety,cleaning, or to prevent unwanted use. The touchpads will notfunction when locked.Note: The touchpads and oven doors cannot be locked ifthe oven temperature is 400° F or above.Fault CodesBAKE or LOCK may flash rapidly in the display to alert you ifthere is an error or a problem. If BAKE or LOCK flash in thedisplay, press the Cancel pad. If BAKE or LOCK continue toflash, disconnect power to the appliance. Wait a few minutes,and then reconnect power. If the flashing still continues,disconnect power to the appliance and call an authorizedservicer.0UpperCancelCook &HoldTimer1Adjusting Sound LevelThe factory default setting for sound is medium (MEd), but itcan be changed to low (Lo) or high (HI). To change thesetting:1. Press and hold Delay and Upper Cancel pads for threeseconds. A beep will sound. “bEEP” and the current soundlevel (“LO”, “MEd” or “HI”) will appear in the display.2. Press the Autoset pad to increase or decrease the soundlevel.3. Wait four seconds and the new setting will be accepted.4. If the Autoset pad is not pressed within 30 seconds, thecontrol will return to the existing setting.Changing Temp °F/°CThe factory default setting for temperature is Fahrenheit. Tochange the setting:1. Press and hold the upper oven Bake and Upper Cancelpads for 3 seconds. A beep will sound and the currentsetting °F or °C will appear in the display.2. Press the Autoset pad to change the setting between °Fand °C.If the oven is currently in use, the touchpads and doorscannot be locked.The current time of day will remain in the display when thetouchpads and doors are locked.To lock both doors:1. Press and release Cancel pad.2. Press and hold the Upper Cancel and Cook& Hold pads for three seconds.• OFF appears in the display• LOCK flashes while the doors are locking.Both oven doors lock. LOCK remains in the display.To unlock both doors:Press and hold the Upper Cancel and Cook & Hold pads forthree seconds. OFF disappears from the display and LOCKflashes while the doors are unlocking.Timer2Timer1Timer2