Tascam HS-20 Owner's Manual

Contents

88 TASCAM HS-2010 – Internal settingsDelete After UploadSet whether or not files that have been uploaded areautomatically deleted.o Disable (default): Uploaded files will not be deletedautomatically.o Enable: Uploaded files will be deleted automatically.TimingSet the time when uploaded files will be automaticallydeletedSoon (default), at 00:00 – at 23:30 (in 30 minute increments)NOTEWhen set to Soon, files will be deleted soon after theycomplete uploading.With all other settings, the files will be deleted at the settime.Network functions (FTP server/telnet/VNC)8 FTP (File Transfer Protocol) serverUse an FTP client application to transfer files between thisunit and a computer. Connect with this unit and log in likeother FTP servers.Connect with this unit and log in to view "A:", "B:" and "C:" inthe root directory. These correspond to the SD card, CF cardand USB flash drive, respectively.If there is no media loaded, the contents of the corre-sponding directory (A, B or C) will not be shown.NOTE• Use an FTP application which is compatible with Unicode ifyou want to display Japanese characters.• Be sure to set the maximum simultaneous transfer numberof the FTP client application to "1" for best network perfor-mance.• Consult with TASCAM Customer Support for details on FTPclient applications that have been tested with this unit.o Settings necessary to connect via FTPThe settings necessary to connect by FTP with this unit areas follows.IP Address: The IP Address of this unit is shown on theNETWORK page of the REMOTE SETUP screen.Port number: 21User name: ”HS-20”Uppercase and lowercase letters are distinguished. (Youcannot change this)Password: The default password is “HS-20”.Uppercase and lowercase letters are distinguished.You can change the password with the Password[Change…] button on the NETWORK page of theREMOTE SETUP screen.NOTE• If the EXTERNAL Control on the LOCK SETUP screen is set asLOCK, you cannot connect via FTP.• If the External LOCK setting is enable when an FTPconnection is active, that FTP connection will be discon-nected.• If you change the setting on the NETWORK page of theREMOTE SETUP screen when there is an FTP connection, itwill be disconnected.o File operations using an FTP client application1. Reading files from this unit.Reading files from this unit is always possible.2. Adding new files to this unitAdding new files to this unit is always possible.If a BWF file or WAV file is added to the current folderduring recording, it will be displayed in the list in theorder of already existing files, recorded files and addedfiles.3. Overwriting existing files on this unitOverwriting the current take is possible only whenstopped.Takes that are being used on the ADJUST ENTRY screenof the playlist mode cannot be overwritten. Overwritingother existing files is always possible.However, if the Play Mode is set to All Take on theGENERAL page of the PLAY SETUP screen duringplayback, overwriting the take that follows the currenttake might not be possible depending on the timing.CAUTIONIf you overwrite a take assigned as a playlist entry in playlistmode, a “?” mark is shown on the applicable entry icon onthe ENTRY list or file ASSIGN screen, and the entry will nolonger be playable. To play the overwritten file assign it tothe entry again.CAUTIONIf the size, number of channels, bit length or samplingfrequency of the new audio file is different from theoverwritten file, it might not be compatible with the existingtimeline or playlist.If you attempt to start play back with such a mismatch, thefollowing error message might appear.Perform the following to resolve the mismatch and avoid theerror message.Timeline mode: Delete the applicable regionTake mode: Delete the applicable take from the card.Playlist Mode: Assign the overwritten file on the entryagain.CAUTIONDo not overwrite an existing audio file with a file with adifferent sampling frequency. Doing so could make it impos-sible to resolve the mismatch.