No. Name Description Range Def.Control Mode Addr.Hex Pg.V/f OLV PMF7-19 Web Page AccessSelects the mode for modification on the Ethernet option board Web pagesettings.0: All access1: Only during stop2: Never0 to 2 0 A A A 3F7F7-20 Gateway selection 0: Gateway not used1: Use Gateway 0 or 1 1 A A A 3F8F7-21 Communication loss time out Multiplier for communication loss detection timeout value. 0 to 300 0 A A A 3F9u H Parameters: Multi-Function TerminalsH parameters assign functions to the multi-function input and output terminals.No. Name Description Range Def.ControlMode Addr.Hex Pg.V/f OLV PMH1: Multi-Function Digital InputH1 parameters to assign functions to the multi-function digital input terminals. Unused terminals should be set to "F".H1-01 Multi-Function Digital Input Terminal S1 Function SelectionSelects the function of terminals S1 to S7Refer to H1 Multi-Function Digital InputSelections on page 306 for a description ofsetting values.1 to 9F <40>40 A A A 438 —H1-02 Multi-Function Digital Input Terminal S2 Function Selection 41 A A A 439 —H1-03 Multi-Function Digital Input Terminal S3 Function Selection 24 A A A 400 —H1-04 Multi-Function Digital Input Terminal S4 Function Selection 14 A A A 401 —H1-05 Multi-Function Digital Input Terminal S5 Function Selection 3(0)<18> A A A 402 —H1-06 Multi-Function Digital Input Terminal S6 Function Selection 4(3)<18> A A A 403 —H1-07 Multi-Function Digital Input Terminal S7 Function Selection 6(4)<18> A A A 404 —<18> Parenthetical value is the default when parameter A1-03 = 3330 3-Wire Initialization.<40> The availability of certain functions depends on the control method used.H1 Multi-Function Digital Input SelectionsH1-o Setting Function Description Control Mode Pg.V/f OLV PM0 3-Wire Sequence Closed: Reverse rotation (only if the drive is set up for 3-wire sequence) O O O —1 Local/Remote Selection Open: Remote, Reference 1 or 2 (b1-01/02 or b1-15/16)Closed: Local, LED operator is run and reference source O O O —2 External Reference 1/2 Open: Run and frequency reference source 1 (b1-01/02)Closed: Run and frequency reference source 2 (b1-15/16) O O O —3 Multi-Step Speed Reference 1Used to select Multi-Step Speeds set in d1-01 to d1-16O O O —4 Multi-Step Speed Reference 2 O O O —5 Multi-Step Speed Reference 3 O O O —6 Jog Reference Selection Open: Selected speed referenceClosed: Jog Frequency reference (d1-17). Jog has priority over all other reference sources. O O O —7 Accel/Decel Time 1 Used to switch between Accel/Decel. Time 1/2 O O O —8 Baseblock Command (N.O.) Open: Normal operationClosed: No drive output O O O —9 Baseblock Command (N.C.) Open: No drive outputClosed: Normal operation O O O —A Accel/Decel Ramp Hold Closed: The drive pauses during acceleration or deceleration and maintains the output frequency. O O O —B Drive Overheat Alarm (OH2) Closed: Displays an OH2 alarm O O O —C Terminal A2 Enable Open: Terminal A2 disabledClosed: Terminal A2 enabled O O O —F Not used Select this setting when not using the terminal or when using the terminal in a pass-through mode. O O O —10 Up Command Open: Maintains the current frequency referenceClosed: Increases or decreases the current frequency reference.Ensure that the increase and decrease commands are set in conjunction with one another. Thefrequency reference source must be set to operator (b1-01 = 0).O O O —11 Down Command O O O —12 Forward Jog Closed: Runs forward at the Jog Frequency d1-17. O O O —13 Reverse Jog Closed: Runs reverse at the Jog Frequency d1-17. O O O —14 Fault Reset Closed: Resets faults if the cause is cleared and the Run command is removed. O O O —15 Fast-Stop (N.O.) Closed: Decelerates at the Fast-Stop time C1-09.To restart the Fast-Stop input must be released and Run must be cycled. O O O —16 Motor 2 Selection Open: Motor 1 (E1-oo, E2-oo)Closed: Motor 2 (E3-oo, E4-oo) O O O —17 Fast-stop (N.C.) Open: Decelerates according to C1-09 (Fast-stop Time) O O O —18 Timer Input Function Set the timer delay using parameters b4-01 and b4-02.Ensure this function is set in conjunction with the multi-function output timer (H2-oo= 12). O O O —19 PID Disable Closed: PID control disabled O O O —1A Accel/Decel Time Selection 2 Switches Accel/Decel times. O O O —1B Program Lockout Open: Parameters can not be edited. (except U1-01 if reference source is set for operator)Closed: Parameters may be edited and saved. O O O —1E Reference Sample Hold Closed: Samples the analog frequency reference and operates the drive at that speed. O O O —B.2 Parameter Table306 YASKAWA ELECTRIC SIEP C710606 18A YASKAWA AC Drive – V1000 Technical Manual (Preliminary)
