ModelCIMR-Vo2A Terminal Screw Size TighteningTorqueN•m (lb.in.)ApplicableGaugemm2 (AWG)RecommendedGaugemm2 (AWG)Line Type0030R/L1, S/L2, T/L3, U/T1, V/T2, W/T3, -, +1, +2 M4 1.2 to 1.5(10.6 to 13.3) 5.5 to 14(10 to 6) 8(8) Note 1 on page41B1, B2 M4 1.2 to 1.5(10.6 to 13.3) 2.0 to 5.5(14 to 10) 5.5(10) Note 1 on page41M5 2 to 2.5(17.7 to 22.1) 5.5 to 14(10 to 6) 8(8) Note 1 on page410040R/L1, S/L2, T/L3, U/T1, V/T2, W/T3, -, +1, +2 M4 1.2 to 1.5(10.6 to 13.3) 5.5 to 14(10 to 6) 14(6) Note 1 on page41B1, B2 M4 1.2 to 1.5(10.6 to 13.3) 2.0 to 5.5(14 to 10) 5.5(10) Note 1 on page41M5 2 to 2.5(17.7 to 22.1) 5.5 to 14(10 to 6) 8(8) Note 1 on page410056R/L1, S/L2, T/L3, U/T1, V/T2, W/T3, -, +1, +2 M6 4 to 6(35.4 to 53.1) 14 to 22(6 to 4) 22(4) Note 1 on page41B1, B2 M5 2 to 2.5(17.7 to 22.1) 5.5 to 8(10 to 8) 8(8) Note 1 on page41M6 4 to 6(35.4 to 53.1) 14 to 22(6 to 4) 22(4) Note 1 on page410069R/L1, S/L2, T/L3, U/T1, V/T2, W/T3, -, +1, +2 M8 9 to 11(79.7 to 11.0) 8 to 38(8 to 2) 38(2) Note 1 on page41B1, B2 M5 2 to 2.5(17.7 to 22.1) 8 to 14(8 to 6) 14(6) Note 1 on page41M6 4 to 6(35.4 to 53.1) 8 to 22(8 to 4) 22(4) Note 1 on page41n Three-Phase 400 V ClassTable 3.4 Wire Gauge and Torque SpecificationsModelCIMR-Vo4A Terminal Screw Size Tightening TorqueN•m (lb.in.)Applicable Gaugemm2 (AWG)Recommended Gaugemm2 (AWG) Line Type00010002000400050007R/L1, S/L2, T/L3, U/T1, V/T2, W/T3, –, +1, +2, B1,B2, M4 1.2 to 1.5(10.6 to 13.3) 2.0 to 5.5(14 to 10) 2(14) Note 1 on page410009R/L1, S/L2, T/L3, U/T1, V/T2, W/T3, –, +1, +2, B1,B2 M4 1.2 to 1.5(10.6 to 13.3) 2.0 to 5.5(14 to 10) 2(14) Note 1 on page41M4 1.2 to 1.5(10.6 to 13.3) 2.0 to 5.5(14 to 10) 3.5(12) Note 1 on page410011R/L1, S/L2, T/L3, U/T1, V/T2, W/T3, –, +1, +2, B1,B2 M4 1.2 to 1.5(10.6 to 13.3) 2.0 to 5.5(14 to 10) 2(14) Note 1 on page41M4 1.2 to 1.5(10.6 to 13.3) 2.0 to 5.5(14 to 10) 3.5(12) Note 1 on page410018R/L1, S/L2, T/L3, U/T1, V/T2, W/T3, -, +1, +2 M4 1.2 to 1.5(10.6 to 13.3) 2.0 to 5.5(14 to 10) 5.5(10) Note 1 on page41B1, B2 M4 1.2 to 1.5(10.6 to 13.3) 2.0 to 5.5(14 to 10) 5.5(10) Note 1 on page41M5 2 to 2.5(17.7 to 22.1) 5.5 to 14(10 to 6) 5.5(10) Note 1 on page410023R/L1, S/L2, T/L3, U/T1, V/T2, W/T3, -, +1, +2 M4 1.2 to 1.5(10.6 to 13.3) 5.5 to 14(10 to 6) 8(8) Note 1 on page41B1, B2 M4 1.2 to 1.5(10.6 to 13.3) 2.0 to 5.5(14 to 10) 5.5(10) Note 1 on page41M5 2 to 2.5(17.7 to 22.1) 5.5 to 14(10 to 6) 5.5(10) Note 1 on page410031R/L1, S/L2, T/L3, U/T1, V/T2, W/T3, -, +1, +2 M5 2 to 2.5(17.7 to 22.1) 5.5 to 14(10 to 6) 8(8) Note 1 on page41B1, B2 M5 2 to 2.5(17.7 to 22.1) 5.5 to 8(10 to 8) 8(8) Note 1 on page41M6 4 to 6(35.4 to 53.1) 5.5 to 14(10 to 6) 8(8) Note 1 on page410038R/L1, S/L2, T/L3, U/T1, V/T2, W/T3, -, +1, +2 M5 2 to 2.5(17.7 to 22.1) 5.5 to 14(10 to 6) 14(6) Note 1 on page41B1, B2 M5 2 to 2.5(17.7 to 22.1) 5.5 to 8(10 to 8) 8(8) Note 1 on page41M6 4 to 6(35.4 to 53.1) 5.5 to 14(10 to 6) 8(8) Note 1 on page41u Main Circuit Terminal Power Supply and Motor WiringThis section outlines the various steps, precautions, and checkpoints for wiring the main circuit terminals and motor terminals.NOTICE: When connecting the motor to the drive output terminals U/T1, V/T2, and W/T3, the phase order for the drive and motor should match. Failure to comply with properwiring practices may cause the motor to run in reverse if the phase order is backward.NOTICE: Do not connect phase-advancing capacitors or LC/RC noise filters to the output circuits. Improper application of noise filters could result in damage to the drive.NOTICE: Do not connect the AC power line to the output motor terminals of the drive. Failure to comply could result in death or serious injury by fire as a result of drive damagefrom line voltage application to output terminals.3.6 Main Circuit Wiring42 YASKAWA ELECTRIC SIEP C710606 18A YASKAWA AC Drive – V1000 Technical Manual (Preliminary)
