5.7 H: Terminal FunctionsH parameters are used to assign functions to the external terminals.u H1: Multi-Function Digital Inputsn H1-01 to H1-07: Functions for Terminals S1 to S7These parameters assign functions to the multi-function digital inputs. Settings 0 to 9F determine function for each terminaland are explained below.Note: 1. Terminals that are not used and terminals using the through-mode should be set to “F”.2. Drive software versions PRG: 1013 and later require that the Forward run and Reverse Run commands be set simultaneously.No. Parameter Name SettingRange DefaultH1-01 Digital Input S1 Function Selection 1 to 9F 40: Forward Run Command (2-wire sequence)H1-02 Digital Input S2 Function Selection 1 to 9F 41: Reverse Run Command (2-wire sequence)H1-03 Digital Input S3 Function Selection 0 to 9F 24: External Fault (N.O., always detected, coast to stop)H1-04 Digital Input S4 Function Selection 0 to 9F 14: Fault ResetH1-05 Digital Input S5 Function Selection 0 to 9F 3 (0) <1> : Multi-Step Speed Reference 1H1-06 Digital Input S6 Function Selection 0 to 9F 4 (3) <1> : Multi-Step Speed Reference 2H1-07 Digital Input S7 Function Selection 0 to 9F 6 (4) <1> : Jog Reference Selection<1> Number appearing in parenthesis is the default value after performing a 3-Wire initialization.Table 5.25 Digital Multi-Function Input SettingsSetting Function Page0 3-Wire Sequence 1771 LOCAL/REMOTE Selection 1772 External Reference 1/2 1773 Multi-Step Speed Reference 11784 Multi-Step Speed Reference 25 Multi-Step Speed Reference 36 Jog Reference Selection 1787 Accel/Decel Time 1 1788 Baseblock Command (N.O.) 1789 Baseblock Command (N.C.)A Accel/Decel Ramp Hold 178B Drive Overheat Alarm (oH2) 178C Terminal A1/A2 Enable/Disable 178F Not used/Through Mode 17910 Up Command 17911 Down Command12 Forward Jog 18013 Reverse Jog14 Fault Reset 18015 Fast-Stop (N.O.) 18016 Motor 2 Selection 18117 Fast-stop (N.C.) 18018 Timer Function Input 18119 PID Disable 1811A Accel/Decel Time Selection 2 1811B Program Lockout 1811E Reference Sample Hold 18120 to 2F External Fault 18230 PID Integral Reset 18231 PID Integral Hold 183Setting Function Page32 Multi-Step Speed Reference 4 18334 PID Soft Starter Cancel 18335 PID Input Level Selection 18340 Forward Run/Stop (2-wire sequence) 18341 Reverse Run/Stop (2-wire sequence)42 Run/Stop (2-Wire sequence 2) 18343 FWD/REV (2-Wire sequence 2)44 Offset Frequency 1 Addition18345 Offset Frequency 2 Addition46 Offset Frequency 3 Addition47 <1> Node Setup 18360 DC Injection Braking Command 18361 External Speed Search Command 1 18462 External Speed Search Command 265 KEB Ride-Thru 1 (N.C.) 18466 KEB Ride-Thru 1 (N.O.)67 Communications Test Mode 18468 High-Slip Braking 1846A Drive Enable 18475 Up 2 Command 18476 Down 2 Command7A KEB Ride-Thru 2 (N.C.) 1857B KEB Ride-Thru 2 (N.O.)7C Short-Circuit Braking (N.O.) 1857D Short-Circuit Braking (N.C.)7E Forward/Reverse Detection (V/f Control withSimple PG Feedback) 18690 to 96 DriveWorksEZ Digital Inputs 1 to 7 1869F DriveWorksEZ Disable 186<1> Available in drive software versions PRG: 1016 and later.5.7 H: Terminal Functions176 YASKAWA ELECTRIC SIEP C710606 16C YASKAWA AC Drive – V1000 Technical Manual
