<3> Range upper limit is dependent on parameters E1-04, Maximum Output Frequency, and d2-01, Frequency Reference Upper Limit.<4> Default setting is determined by the drive software version.PRG: 1016 and later: 100.00%PRG: 1015 and earlier: 0.00 %u E: Motor ParametersNo. Name Description Range Def.ControlMode Addr. Hex Pg.V/f OLV PME1: V/f Pattern CharacteristicsUse E1 parameters to set V/f characteristics for the motor.E1-01<1> Input VoltageSettingThis parameter must be set to the power supply voltage. Itsets the maximum and base voltage used by preset V/fpatterns (E1-03 = 0 to E) and adjusts levels used by certainfunctions.WARNING! Electrical Shock Hazard. Drive inputvoltage (not motor voltage) must be set in E1-01 for theprotective features of the drive to function properly. failureto do so may result in equipment damage and/or death orpersonal injury.155 to 255 200 V S S S 300 162E1-03<2>V/f PatternSelectionSelects a preset V/f pattern.0: 50 Hz Constant torque 11: 60 Hz Constant torque 22: 60 Hz Constant torque 3 (50 Hz base)3: 72 Hz Constant torque 4 (60 Hz base)4: 50 Hz Variable torque 15: 50 Hz Variable torque 26: 60 Hz Variable torque 37: 60 Hz Variable torque 48: 50 Hz High starting torque 19: 50 Hz High starting torque 2A: 60 Hz High starting torque 3B: 60 Hz High starting torque 4C: 90 Hz (60 Hz base)D: 120 Hz (60 Hz base)E: 180 Hz (60 Hz base)F: Custom V/f. E1-04 through E1-13 settings define theV/f pattern0 to F F A A − 302 162E1-04 Maximum OutputFrequencyE1-04 and E1-06 to E1-13 can only be changed whenE1-03 is set to F. To set linear V/f characteristics, set thesame values for E1-07 and E1-09. In this case, the settingfor E1-08 will be disregarded.When E1-13 = 0.0 V, then the drive uses the value set toE1-05 to control the voltage level.Ensure that the five frequencies are set according to theserules to prevent triggering an oPE10 fault:E1-09 ≤ E1-07 < E1-06 ≤ E1-11 ≤ E1-04Note: Setting E1-11 to 0 disables both E1-11 and E1-12,and the above conditions do not apply.E1-09 E1-07 E1-06 E1-11 E1-04E1-05E1-12E1-13E1-08E1-10VACrms Out(V)Frequency (Hz)40.0 to400.0<3>60 Hz<4><19>S S S 303 165E1-05<1> Maximum OutputVoltage 0.0 to255.0200 V<4> S S S 304 165E1-06 Base Frequency 0.0 toE1-0460 Hz<4> <19> S S S 305 165E1-07 Middle OutputFrequency 0.0 toE1-043.0 Hz<3><19>A A - 306 165E1-08<1> Middle OutputFrequency Voltage 0.0 to255.016.0 V<5> <6> A A - 307 165E1-09 Minimum OutputFrequency 0.0 toE1-041.5 Hz<5> <4><19>S S S 308 165E1-10<1> Minimum OutputFrequency Voltage 0.0 to255.09.0 V<5> <6> A A - 309 165E1-11 Middle OutputFrequency 2 0.0 toE1-04 0.0 Hz A A - 30A 165E1-12<1><7>Middle OutputFrequency Voltage20.0 to255.0 0.0 V A A - 30B 165E1-13<1> <9> Base Voltage 0.0 to255.0 0.0 V A S - 30C 165E2: Motor ParametersUse E2 parameters to set motor-related data.B.2 Parameter Table342 YASKAWA ELECTRIC SIEP C710606 16C YASKAWA AC Drive – V1000 Technical Manual
