No. Name Description Range Def.ControlMode Addr.Hex Pg.V/fOLVPMT1-00 Motor Selection1/2Selects which set of motor parameters are used and set duringAuto-Tuning. If Motor 2 selection (H1-oo = 16) is not selected,this parameter will not be displayed.1: Motor 1 (sets E1-oo, E2-oo)2: Motor 2 (sets E3-oo, E4-oo. This selection is not displayedif motor 2 has not been selected.)1, 2 1 A A − 700 104T1-01 Auto-Tuning ModeSelectionSelects the Auto-Tuning mode.0: Rotational Auto-Tuning2: Stationary Auto-Tuning for Line-to-Line Resistance3: Rotational Auto-Tuning for V/f Control (necessary for EnergySavings and Speed Estimation type Speed Search)0, 2, 3<1>2 or 3 inV/f0 or 2 inOLV2 inMotor 2A A − 701 104T1-02 Motor Rated Power Sets the motor rated power in kilowatts (kW).Note: If motor power is given in horsepower, power in kW canbe calculated using the following formula: kW = HP x 0.746.<2> <3> A A − 702 104T1-03<4> Motor RatedVoltage Sets the motor rated voltage in volts (V). 0.0 to255.5 200.0 V A A − 703 104T1-04 Motor RatedCurrent Sets the motor rated current in amperes (A).10 to200% ofdrive ratedcurrent<3> A A − 704 104T1-05 Motor BaseFrequency Sets the base frequency of the motor in Hertz (Hz). 0.0 to400.0 <5> A A − 705 105T1-06 Number of MotorPoles Sets the number of motor poles. 2 to 48 4 A A − 706 105T1-07 Motor Base Speed Sets the base speed of the motor in revolutions per minute r/min(RPM). 0 to 24000 <6> A A − 707 105T1-11 Motor Iron LossProvides the iron loss for determining the Energy Savingcoefficient.The value set to E2-10 (motor iron loss) when the power is cycled.If T1-02 is changed, an initial value valid for the selected capacitywill be shown.0 to 6553514 W A − − 70B 105These values differ depending on themotor code value and motorparameter settings.<1> The available tuning methods depend on control mode. Select values 2 or 3 in V/f Control, 0 or 2 in OLV control, and 2 for Motor 2 control.<2> Setting range varies depending on drive software version.PRG: 1016 and later: 0.03 to 650.00 kWPRG: 1015 and earlier: 0.00 to 650.00 kW<3> Default setting value is dependent on parameter o2-04, Drive Model Selection.<4> Values shown here are for 200 V class drives. Double the value when using a 400 V class drive.<5> Regional default settings:Setting 60.0 Hz: Japan (Model code: CIMR-VAoA) and Asia (Model code: CIMR-VToA)Setting 50.0 Hz: China (Model code: CIMR-VBoA)<6> Regional default settings:Setting 1750 r/min: Japan (Model code: CIMR-VAoA) and Asia (Model code: CIMR-VToA)Setting 1450 r/min: China (Model code: CIMR-VBoA)u U: MonitorsMonitor parameters allow the user to view drive status, fault information, and other information about drive operation.No. Name Description Analog OutputLevel UnitControlMode Addr.HexV/fOLVPMU1: Operation Status MonitorsUse U1 monitors to display the operation status of the drive.U1-01 Frequency Reference Monitors the frequency 10 V: Maxfrequency 0.01Hz A A A 40U1-02 Output Frequency Displays the output frequency. Display units aredetermined by o1-03. 10 V: Maxfrequency 0.01Hz A A A 41B.2 Parameter TableYASKAWA ELECTRIC SIEP C710606 16C YASKAWA AC Drive – V1000 Technical Manual 371B Parameter List
