Yaesu FT-897D Operating Manual

Also see for FT-897: Manual Brochure & specs Technical supplement Service manual Operating manual

Contents

Page 55FT-897D OPERATING MANUALMENU O PERATIONNo Menu Item040 DIG VOX041 DISP COLOR042 DISP CONTRAST043 DISP INTENSITY044 DISP MODE045 DSP BPF WIDTH046 DSP HPF CUTOFF047 DSP LPF CUTOFF048 DSP MIC EQ049 DSP NR LEVEL050 EMERGENCY051 FM MIC GAIN052 FM STEP053 HOME-->VFO054 LOCK MODE055 MEM GROUP056 MEM TAG057 MEM/VFO DIAL MODE058 MIC SCAN059 MIC SEL060 MTR ARX SEL061 MTR ATX SEL062 MTR PEAK HOLD063 NB LEVEL064 OP FILTER 1065 PG A066 PG B067 PG C068 PG ACC069 PG P1070 PG P2071 PKT 1200072 PKT 9600073 PKT RATE074 PROC LEVEL075 RF POWER SET076 RPT SHIFT077 SCAN MODE078 SCAN RESUME079 SPLIT TONE080 SQL/RF GAIN081 SSB MIC GAIN082 SSB STEP083 TONE FREQ084 TOT TIME085 TUNER/ATAS086 TX IF FILTER087 VOX DELAY088 VOX GAIN089 XVTR A FREQ090 XVTR B FREQ091 XVTR SELFunctionSets the gain of the VOX circuitry’s input level for the DIG mode.Selects the illumination color for each operating status.Setting of the display contrast level.Setting of the display brightness level.Sets up the LCD Lamp mode.Setting of the bandwidth for the DSP CW audio filter.Adjusts the low-cut characteristics of the DSP HPF filter.Adjusts the high-cut characteristics of the DSP LPF filter.Sets the DSP microphone equalization pattern.Setting of the degree of DSP Noise Reduction.Enables Tx/Rx operation on the Alaska Emergency Channel,5167.5 kHz.Adjusts the microphone gain level for the FM mode.Selects the tuning steps for the MEM/VFO CH knob in the FMmode.Enables/disables the moving of HOME channel data to the VFO.Selects the operation of the front panel’s LOCK key.Enables/disables the memory grouping feature.Stores Alpha-Numeric “Tags” for the memory channels.Selects the function which is engaged when you press the MEM/VFO CH knob.Enables/disables scanning access via the microphone’s [UP]/[DWN] keys.The choice of the equipment which connects to the MIC jack.Select the meter display configuration while the transceiver isreceiving.Selects the meter display configuration while the transceiver istransmitting.Enabling/disabling of the “peak hold” function of the meter.Setting of the blanking level for the IF Noise Blanker.Not available at this time.Programming the [A] key (in the Operating Function Row 17)function.Programming the [B] key (in the Operating Function Row 17)function.Programming the [C] key (in the Operating Function Row 17)function.Programming the optional MH-59A8J microphone’s [ACC]button assignment.Programming the optional MH-59A8J microphone’s [P1] buttonassignment.Programming the optional MH-59A8J microphone’s [P2] buttonassignment.Adjusts the audio input level from the TNC during 1200 bps Packetoperation.Adjusts the audio input level from the TNC during 9600 bps Packetoperation.Sets the transceiver’s circuitry for the Packet baud rate to be used.Sets the compression level for the AF speech processor in theSSB/AM modes.Setting of the maximum power level for the current band.Sets the magnitude of the repeater shift.Selects the desired Scan-Resume mode.Sets the delay time for scanning resumption.Enables/disables split CTCSS/DCS cording.Selects the configuration of the front panel’s SQL/RF knob.Adjusts the microphone gain level for the SSB mode.Selects the tuning steps for the MEM/VFO CH knob on the SSBmode.Setting of the CTCSS Tone Frequency.Select the Automatic Power Off time.Selects the device (FC-30 or ATAS-100/-120) to be controlled viathe front panel’s [A](TUNE) key.Selects the Transmit IF filter.Sets the “hang time” for the VOX circuitry.Sets the gain of the VOX circuitry’s input audio detector.Allows an arbitrary frequency to be set on the display, to allowdirect frequency readout during transverter operation.Enables/disables/selects the antenna port to be used forTransverter operation.Available Values Default0 ~ 100 0– –0 ~ 13 50 (Dim) ~ 3 (Bright) 3OFF/AUTO1/AUTO2/ON AUTO260/120/240 Hz 240 Hz100 ~ 1000 Hz 100 Hz1000 ~ 6000 Hz 6000 HzOFF/LPF/HPF/BOTH OFF1 ~ 16 8ON/OFF OFF0 ~ 100 505/6.25/10/12.5/15/20/25/ 250 kHzON/OFF ONDIAL/FREQ/PANEL/ALL DIALON/OFF OFF– –CW SIDETONE, CW SPEED,MHz/MEM GRP, MIC GAIN, MHz/MEM GRPNB LEVEL, RF POWER, STEPON/OFF ONNOR/RMT/CAT NORSIG, CTR, VLT, N/A, FS, OFF SIGPWR, ALC, MOD, SWR, PWRVLT, N/A, OFFON/OFF ON0 ~ 100 50– –MONIQ.SPLATCMONIQ.SPLTCALL0 ~ 100 500 ~ 100 501200/9600 (bps) 1200 bps0 ~ 100 505 ~ 100 1000.00 ~ 99.99 (MHz) 2TIME/BUSY/STOP TIME1 ~ 10 (sec) 5 secON/OFF OFFRF-GAIN/SQL 10 ~ 100 501kHz/2.5kHz/5kHz 2.5 kHz50 Standard CTCSS tones 88.5 HzOFF/1 ~ 20 (min) OFFOFF/ATAS(HF)/ATAS(HF&50) OFF/ATAS(ALL)/TUNERCFIL/FIL1/FIL2 CFIL100 ~ 3000 (ms) 500 ms1 ~ 100 5000,000,00 ~ 99,999,99 (kHz) –OFF/X VTR A/X VTR B OFFAll Multi Function, all MenuItem, MONI, Q.SPL, TCALL,ATC, and USER.1: Depends Mon transceiver version.2: Depends on operating band and transceiver version.