Yaesu FT-897D Operating Manual

Also see for FT-897: Manual Brochure & specs Technical supplement Service manual Operating manual

Contents

Page 58 FT-897D OPERATING MANUALMENU MODE No- 030 [CW SPEED]Function: Sets the sending speed for the built-in Electronickeyer.Available Values: 4wpm ~ 60 wpm (1wpm/step)/20cpm ~300 cpm (5cpm/step)Default: 12 wpm (60 cpm)You can set the sending speed according to either of twounits of speed (wpm: words per minute; cpm: charactersper minute)To switch units between “wpm” and “cpm,” just press theMEM/VFO CH knob.MENU MODE No•031 [CW TRAINING]Function: Sends random Morse Code five-character groupsvia the sidetone.Available Values: N / A / ANDefault: NN: Numeric characters onlyA: Alphabet characters onlyAN: Numeric and Alphabet characters (Mixed)MENU MODE No•032 [CW WEIGHT]Function: Sets the Dot:Dash ratio for the built-in electronickeyer.Available Values: 1:2.5 ~ 1:4.5Default: 1:3.0MENU MODE No- 033 [DCS CODE]Function: Setting of the DCS code.Available Values: 104 Standard DCS codesDefault: 023You can set the DSC codes for Encode and Decode sepa-rately.To switch between “ENCODE” and “DECODE,” just pressthe MEM/VFO CH knob.MENU MODE No •034 [DCS INV]Function: Selects “Normal” or “Inverted” DCS coding.Available Values: Tn-Rn/Tn-Riv/Tiv-Rn/Tiv-RivDefault: Tn-Rn“n” = “normal”“iv” = “inverted”MENU MODE No- 035 [DIAL STEP]Function: Setting of the DIAL knob’s tuning speed.Available Values: FINE/COARSEDefault: FINEYou may choose between two speeds for the DIAL knob.Selecting “COARSE” doubles the tuning rate compared tothe default value.FINE: 10 Hz/step @SSB/CW mode, 100 Hz/step @AM/FMCOARSE: 20 Hz/step @SSB/CW mode, 200 Hz/step @AM/FMMENU MODE No •036 [DIG DISP]Function: Defines the displayed frequency offset duringDIG (USER-L or USER-U) mode operation.Available Values: –3000 ~ +3000 HzDefault: 0 HzMENU MODE No•037 [DIG GAIN]Function: Adjusts the audio input level from terminal equip-ment (such as a TNC or PSK-31 sound card) during DIG(Digital) mode operation.Available Values: 0 ~ 100Default: 50MENU MODE No•038 [DIG MODE]Function: Selects the mode and sideband (if applicable) inthe DIG (Digital) mode.Available Values: RTTY-L/RTTY-U/PSK31-L/PSK31-U/USER-L/USER-UDefault: RTTY-LRTTY-L: AFSK RTTY operation on the LSB modeRTTY-U: AFSK RTTY operation on the USB modePSK31-L: PSK-31 operation on the LSB modePSK31-U: PSK-31 operation on the USB modeUSER-L: User-programmed costume operation based onLSB modeUSER-U: User-programmed costume operation based onUSB modeIn the USER-L and USER-U modes, you candefine the display frequency offset and carrierfrequency offset by Menu Mode No-036 [DIGDISP] and No-039 [DIG SHIFT].MENU MODE No•039 [DIG SHIFT]Function: Defines the carrier frequency offset during DIG(USER-L or USER-U) mode operation.Available Values: –3000 ~ +3000 HzDefault: 0 HzMENU MODE No •040 [DIG VOX]Function: Sets the gain of the VOX circuitry’s input levelfor the DIG mode.Available Values: 0 ~ 100Default: 0Note: When you wish to use “DIG VOX,” press the [F] keymomentarily, then rotate the MEM/VFO CH knob, until youreach Multi Function Row “d” [RPT, REV, VOX], then pressthe [C](VOX) key. The parentheses and “ ” icon will dis-appear, signifying that the (SSB/AM/FM voice) VOX sys-tem has been turned off. Despite these indicators havingdisappeared, the Digital Mode “VOX” system will still beactive, allowing audio input from a TNC or sound card toengage the transmitter.MENU MODE No- 041 [DISP COLOR]Function: Selects the illumination color for each operatingstatus.Available Values: ARTS/BAND/FIX/MEMGRP/MODE/MTR/VFODefault: FIXMENU MODE No- 042 [DISP CONTRAST]Function: Setting of the display contrast level.Available Values: 1 ~ 13Default: 5MENU O PERATION