Contents - revision history
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- General
- Description
- Management
- Primary Shelf
- Expansion Shelves
- Features
- Operation
- Remote Alarm Indication (RAI)
- Front Panel LEDs
- Pushbuttons
- Instructions for Installing the Module
- Provisioning
- User Interface
- Menu Navigation
- Menu Trees
- Figure 4. Provisioning Menu Tree
- Figure 5. Advanced Provisioning Menu Tree
- Figure 6. ATM Provisioning Slot/Port Menu Tree
- Figure 7. ATM Provisioning (DS3) Menu Tree
- Figure 8. Traffic Descriptor Menu Tree
- Figure 9. VC/VP Provisioning Menu Tree
- Figure 10. Software Upgrade Menu Tree
- Figure 11. Test Menu Tree
- Figure 12. Performance Monitoring Menu Tree
- Figure 13. ATM Performance Monitoring Menu Tree
- Menu Descriptions
- Configuration Screen
- Provisioning Menu
- PSM Advanced Provisioning Menu
- System Buffer, CAC, & Policing Options Menu
- Table 13. System Buffer, CAC, & Policing Menu Options
- Table 14. System Buffer, CAC, & Policing Options Menu Hot Keys
- WAN Direction (Network) Buffer, CAC, & Policing Options Menu
- Table 16. WAN Direction (Network) Buffer, CAC, & Policing Options Menu Hot Keys
- Loop Direction Buffer, CAC, & Policing Options Menu
- Table 18. Loop Direction Buffer, CAC, & Policing Options Menu Hot Keys
- Shelf # Slot # Port # Buffer, CAC, & Policing Options Menu
- Table 20. Shelf # Slot # Port # Buffer, CAC, & Policing Options Menu Hot Keys
- Alarms Provisioning Menu
- DS3 and Timing Provisioning Menu
- Framing Menu
- Primary Timing Menu
- Secondary Timing Menu
- ATM Provisioning Screen - Shelf # Slot # Port # Menu
- Table 27. ATM Provisioning Screen - Shelf # Slot # Port # Menu Hot Keys
- ATM Provisioning Screen - Shelf # Slot # Port # (PNNI Port Options) Menu
- ILMI Provisioning Screen
- ATM Provisioning Screen - DS3 Port Menu
- ATM Provisioning Screen - MGMT Port Menu
- Traffic Descriptor Screen
- Table 33. Traffic Descriptor Screen Hot Keys
- Create Traffic Descriptor Screen
- Table 34. Create Traffic Descriptor Screen Options
- VC/VP Provisioning Screen
- Table 36. VC/VP Provisioning Screen Hot Keys
- Detailed PVC Information Screen
- VC/VP Provisioning - Create PVC/PVP Menu
- Table 38. VC/VP Provisioning - Create PVC/PVP Menu Options
- Table 39. VC/VP Provisioning - Create PVC/PVP Menu Hot Keys
- Search Through VC/VP List Menu
- PNNI Switch Provisioning - Base Menu
- PNNI Switch Provisioning - Lowest Level Node Menu
- Software Upgrade Menu
- Table 44. Software Upgrade Menu Hot Keys
- MDE Link Configuration Menu
- DS3-PSM Status Menu
- DS3 CSM Status Screen
- Line Card Status Screen
- Port Status Screen
- SPVC Status Screen
- Table 52. SPVC Status Screen Hot Keys
- CSM Alarms Screen
- Table 54. CSM Alarms Screen Hot Keys
- Test Menu
- CSM Test Menu
- DS3 Loopbacks Menu
- PVC/PVP Test Screen
- Table 59. VC/VP Test Screen Hot Keys
- VC/VP Test Screen
- OAM Loopback Test Screen
- Insert Cell Test Screen
- CSM Test - Single Card Cell Generation Test Menu
- Table 63. Single Card Cell Generation Test Menu Options
- Performance Monitoring Menu
- Table 65. DS3 Performance Monitoring Definitions
- DS3 CSM Performance Monitoring Menu
- DS3 CSM Daily Menu
- DS3 CSM Far-End Daily Menu
- ATM Performance Monitoring Menu
- Port Performance - DS3 Port Screen
- Port Performance - MGMT Port Screen
- Port Performance - Shelf # Slot #, Port # Screen
- VC/VP Performance - Created VC/VP List Screen
- Table 74. VC/VP Performance - Created VC/VP List Screen Hot Keys
- VC/VP Statistics Screen
- Monitor Session List Screen
- Protection Configuration Menu
- Maintenance
- Warranty and Customer Service
|
Total Access 3000 DSLAM DS3 Primary Switch Module Installation and Maintenance Practice100 61181041L3-5AOAM Loopback Test ScreenThe OAM Loopback Test Screen (see Figure 53) is used to perform OAM Loopback testing. TheOAM Loopback test sends OAM Cells with the loopback indication bit set. The Remote OAM IDmust be entered to identify at which connecting node the loopback should occur. Upon theRemote receiving the OAM Loopback cell, the remote will respond with an OAM cell with theloopback indication bit cleared. For the DS3-PSM to properly respond to OAM loopbacksdirected at it, the OAM ID of the DS3-PSM should be set to a value other than all “6A”s. Whena DS3-PSM has the OAM ID set to the default of all “6A”s, then OAM loopbacks are ignored.Figure 53. OAM Loopback Test ScreenThe OAM Loopback Test Screen options are shown in Table 61.Table 61. OAM Loopback Test Screen OptionsOption Description FunctionINDEX This field displays the index number assigned to the VC/VP.STATUS This field displays the status of the VC/VP as Enabled or Disabled.TYPE This field displays the type as either PVC or PVP.SRV-CL This field displays the Service Class assigned to the PVC (defined by the trafficdescriptor).Endpoint 1 (Top Level)SH/SL/PO This field displays the shelf/slot/port location of the VC/VP Endpoint 1.VPI This field displays the current VPI value of the VC/VP Endpoint 1.VCI This field displays the current VCI value of the VC/VP Endpoint 1.Shelf: 1 Slot: B Total Access System MM/DD/YY HH:MMONLINEOAM LOOPBACK TEST SCREENVC/VP Name: _InbandPVCENDPOINT 1 <-> ENDPOINT 2INDEX STATUS TYPE SH/SL/PO VPI VCI <-> SH/SL/PO VPI VCI SRV-CL1 ENABLED PVC MGMT PORT 0 32 <-> DS3 PORT 0 33 nrtVBR1. Endpoint 1 Remote OAM ID : FF:FFFFFFFFFFFFFFFFFFFFFFFFFFFFFF2. Endpoint 2 Remote OAM ID : FF:FFFFFFFFFFFFFFFFFFFFFFFFFFFFFF3. TYPE OF OAM CELL: SEGMENT4. SEND FROM ENDPOINT1 (toward endpoint 1 eqpt.)5. SEND FROM ENDPOINT2 (toward endpoint 2 eqpt.)6. RESET OAM LOOPBACK STATS--------------------ENDPOINT1--------------------OAM Tx LoopBack Req : 0 OAM Tx LoopBack Rsp : 0OAM Rx LoopBack Req : 0 OAM Rx LoopBack Rsp : 0OAM LoopBack Passed : 0 OAM LoopBack Failed : 0--------------------ENDPOINT2--------------------OAM Tx LoopBack Req : 0 OAM Tx LoopBack Rsp : 0OAM Rx LoopBack Req : 0 OAM Rx LoopBack Rsp : 0OAM LoopBack Passed : 0 OAM LoopBack Failed : 0Selection:
|
