Canon VB-H43 Operation Manual

Also see for VB-H43: Operation guide Installation guide

Contents

[Camera] Setting Initial Camera Settings and External Device Name59Setting Page4When [Haze Compensation] is set to [Auto] and [HazeCompensation Strength (Auto)] is set to [Strong],contrast may be strong if the subject is not obscuredby haze. If this happens, set [Haze CompensationStrength (Auto)] to [Mild].(6) [Pan/Tilt Speed Control]Select [Control at set speed] or [Control by zoomposition] for the pan/tilt control mode. If [Control byzoom position] is selected, the pan/tilt speed will beslower in the telephoto zoom range, and faster inwide-angle zoom range.Note• [Pan/Tilt Speed Control] can also be set using [Pan/Tilt] in theControl for Admin panel of the Admin Viewer (p. 152).• If [Control by zoom position] is selected, [Control for Admin] >[Pan/Tilt] will also be fixed at [Control speed by zoom position].Day/Night (when Auto is set)(1) [Switching Brightness]Set the brightness at which Day Mode and NightMode will be switched when [Auto] is selected in[Day/Night]. Select [Darker], [Slightly Darker],[Standard], [Slightly Brighter] or [Brighter]. Select[Darker] if you want to capture video in color as muchas possible.Select [Brighter] to reduce noise. Note that this modeswitches to black & white sooner.(2) [Response (sec.)]Set the time in seconds needed for judgment onswitching between Day Mode and Night Mode when[Auto] is selected in [Day/Night]. Select [60], [30],[20], [10] or [5].The mode will switch between Day Mode and NightMode if brightness remains above or below the levelset in (1) for the number of seconds specified.Select [30] or [60] if brightness changes frequently,such as when a light source passes in front of thecamera. Select [5] or [10] if change in brightness isminimal.Installation Conditions(1) [Dome]Select whether or not a dome is used. To use thecamera with a dome housing unit, select [Use].(2) [LED Setting]Select [Turn Off] or [Turn On] for the LED operationstatus on the camera. Set to [Turn Off] if you do notwant to turn on the LED.Set to [Turn Off] if an optional indoor dome housing forthe camera is used, if reflected LED light enters thecapture area or otherwise interferes with imagecapture, or if you do not want to show that the camerais operating.(3) [Image Flip]Select [Disable] or [Enable] for the orientation of thecamera video.Note• For the focus ranges when the dome is set to[Use], see the note on p. 58.• The LED will light for severalseconds when booting even if the [LED Setting] is set to [TurnOff].Camera Position Control(1) [Restricted to Presets]Set the camera control preset to [No Restriction] or[Preset Only]. The administrator can limit cameracontrol by non-administrators to preset angles byselecting [Preset Only].(2) [Camera Position without Control]Select either [Do not return to Home Position] or[Return to Home Position] as the action when nocontrol privileges are requested by users and thehome position has already been set.When [Return to Home Position] is selected and nousers have control privileges, the camera movesautomatically to the home position. This functionrequires the home position of the camera be set inadvance. Set the home position using Preset SettingTool (p. 106).Important• [AGC Limit] is disabled when [Exposure] is set to [Manual] or[Auto (Flickerless)] in the Admin Viewer.• Minimum subject illumination may change when [AGC Limit]is set.• If [On2] is selected for [Image Stabilizer], it is best to select avideo size smaller than “960 x 540”.• The image stabilizer is not effective when the subject is shaking.• The image stabilizer is not effective beyond a certain level ofvibration or against momentary vibration.• See “Important” on p. 97, p. 104, p. 110 for precautionarynotes regarding Admin Tools configuration when imagestabilizer is set.• See “Important” on p. 150 for precautionary notes regardingthe Viewer when image stabilizer is set.