Eaton C441R User Manual

Also see for C441 Series: User manual

Contents

35User Manual MN04200002EEffective January 2016C441 Ethernet module user manual(C441R, C441T, C441U, C441V)EATON www.eaton.comClass 45 (0x2D): Softstart ObjectInstance Count: 1Instance List: 1Table 64. S611 Softstart Object Instance AttributesAttrib NV Access DataType Name Description3 V Get BOOL At Ref Indicates whether the softstart is inbypass or not.4 NV Set/Get USINT Soft StartMethod Selects the Ramp Start Method.1=Voltage Ramp (no current limit)2=Current Limit (no voltage ramp)100=Pump start7 NV Set/Get UINT Start Time Motor Start Ramp Time. (deciseconds)13 NV Set/Get USINT Kick StartTime The Amount of Time to Apply a KickStart. (deciseconds)14 NV Set/Get UINT Kick StartInitialTorqueInitial Torque Value for the Kick Start.(%)16 NV Set/Get UINT Stop Time Motor Stop Ramp Time. Minimum timeof 0 without pump option. Minimumtime of 50 with pump stop enabled(deciseconds)101 V Get INT Phase APole Temp Power Pole Temperature. Scaled = x10(°C)102 V Get INT Phase BPole Temp Power Pole Temperature. Scaled = x10(°C)103 V Get INT Phase CPole Temp Power Pole Temperature. Scaled = x10(°C)104 V Get INT Pole Temp Average Power Pole Temperature.Scaled = x10 (°C)105 NV Set/Get UINT InitialMotorTorqueStarting (Initial) Torque Percent.106 NV Set/Get UINT PumpStop Time If supported, the amount of time touse for the pump stop ramp behavior.(seconds)107 NV Set/Get UINT StartMethod Motor Start Method0 = Vramp1 = Limit2 = PumpNote: If special function bit 0 is set,then pump option is available and setas the default, otherwise ramp start (0)is default108 NV Set/Get UINT PhaseSequence Line Voltage Phase Sequence:1 = ABC2 = ACB6.5 EtherNet/IP Object Model for S811+ Soft StarterWhen the Ethernet module is connected to an S811+ soft starter,the presented object model is compliant with the ODVA SoftstartDevice profile (type: 0x17).Full Profile for S811+The table below shows the supported classes of the EthernetModule when connected to an S811+ Soft Starter.Class Object # ofInstances Description0x01(hex) Identity 1 Provides module identity object: See details inprevious section.0x02 MessageRouter 1 Internal object implemented per ODVA specifica-tion0x04 AssemblyObject 16 Binds attributes from multiple objects for accesswith a single Implicit (I/O) connection. See detailsbelow.0x06 ConnectionManager 1 Internal object supporting connection manage-ment. Implemented per ODVA specification0x08 DiscreteInput Point 4 Status information for the discrete Inputs. Seedetails in previous section.0x09 DiscreteOutput Point 2 Status and control for the discrete Outputs. Seedetails In previous section.0x0A Analog InputPoint 1 Status and control for the Analog Input. Seedetails below.0x29 ControlSupervisor 1 Motor control functions. See details In previoussection.0x2C Overload 1 Motor overload protection. See details below.0x20 SoftStart 1 Soft start object, See details below.0x93 VoltageMonitor 1 Vendor Specific object for monitoring motor volt-age. See details below.0xF5 TCP/IPInterface 1 Information about the TCP/IP Interface.Implemented per ODVA specification0xF6 EthernetLink 2 Ethernet link object for each of the 2 Ethernetports on the device. Implemented per ODVAspecification.Object DetailsClass 1 (0x01): Identity ObjectInstance Count: 1Instance List: 1Table 65. S811+ Identity Object Instance AttributesAttrib NV Access DataType Name Description1 V Get UINT CIPVendorIDODVA Assigned VendorIdentification Number.2 V Get UINT CIPDeviceTypeCIP Defined General Product Type.3 V Get UINT ProductCode Vendor Product Code4 V Get UINT FirmwareRev Com Adapter Firmware Rev.