Eaton C441R User Manual

Also see for C441 Series: User manual

Contents

60User Manual MN04200002EEffective January 2016C441 Ethernet module user manual(C441R, C441T, C441U, C441V)EATON www.eaton.comTable 102. Register Definitions for S811+ Soft Starter (Cont.)StartCoil Register Read/Write Name Description (Units)1793 113 R/W Field RelayIdle Action When a communication idle state occursthe relays can execute two types ofbehavior. The behavior is selected on aper bit basis.Bit = Description0 = Relay 11 = Relay 2Bit Value = Description0 = Apply Idle Value1 = No Change1809 114 R/W Field RelayIdle State Communication idle value to be applied.A bitfield where each bit defines anoutput point.Bit Value = Description0 = Turn Relay Off1 = Turn Relay On- 130 R Eth Port 1Speed Actual Actual Ethernet link speed. ( Mbs )2097 132 R Eth Port 1Full DuplexEnabledActual duplex modeTrue = Full DuplexFalse = Half Duplex.- 134 R Eth Port 1AutonegotiateStateActive state of the Auto-Negotiationbehavior.Value = State0 = Link Inactive1 = Auto Negotiation in Progress2 = Auto Negotiation Failed (Defaultused)3 = Auto Negotiation of Duplex Failed(speed ok)4 = Auto Negotiation Success5 = Auto Negotiation Disabled6 = Port Disabled2145 135 R Eth Port 1Enabled This parameter can disable the EthernetPort. Effectively disabling the port.True = Enable PortFalse = Disable Port- 137 R Eth Port 2Speed Actual Actual Ethernet link speed. ( Mbs )2209 139 R Eth Port 2Full DuplexEnabledActual duplex mode.True = Full DuplexFalse = Half Duplex- 141 R Eth Port 2AutonegotiateStateActive state of the Auto-Negotiationbehavior.Value = State0 = Link Inactive1 = Auto Negotiation in Progress2 = Auto Negotiation Failed (Defaultused)3 = Auto Negotiation of Duplex Failed(speed ok)4 = Auto Negotiation Success5 = Auto Negotiation Disabled6 = Port Disabled2257 142 R Eth Port 2Enabled This parameter Indicates whether anEthernet port is enabled.True = Port EnabledFalse = Port Disabled- 143 R Method of IPAllocation The method used to allocate an IPAddress:0 - DHCP1 - Upper three octets from NV andlower octet selected by the dip switchsetting.2 - Full address taken from NV Memory.3 - Restore (hardcoded 192.168.1.254).Table 102. Register Definitions for S811+ Soft Starter (Cont.)StartCoil Register Read/Write Name Description (Units)- 144 R PresentEthernet IPAddressThe active IP address being used on thenetwork.- 146 R PresentEthernetSubnet MaskThe active subnet mask IP address beingused on the network.- 148 R PresentEthernetDefaultGatewayThe active default gateway IP addressbeing used on the network.- 150 R/W StoredEthernet IPAddressThe IP address used in the NV addressselect configuration.- 152 R/W StoredEthernetSubnet MaskThe IP subnet mask used in the NVaddress select configuration.- 154 R/W StoredEthernetDefaultGatewayThe IP default gateway used in the NVaddress select configuration.- 156 R/W Ethernet MACAddress Unique MAC Address assigned to thisdevice.- 159 R/W Modbus ComTimeout Communication timeout for Modbus. 0 =Disable. ( milliseconds )- 160 R/W Modbus TXmode Selects the Modbus Mode.0 - RTU1 - ASCII- 161 R/W Modbus BaudRate Selects the Modbus baud rate.0 - 19.2kb1 - 9.6kb2 - 57.6kb3 - 115.2kb- 162 R/W ModbusAddress Modbus address loaded at startup.- 163 R/W Modbus Parityand Stop Bits Selects the Modbus UART parity andStop Bits.0 - Even/One Stop Bit1 - Odd/One Stop Bit2 - None/Two Stop Bits3 - Even/Two Stop Bits4 - Odd/Two Stop Bits5 - None/One Stop Bit3201 201 R IntercomStatus Present state of the Intercom Link.Bit - Status0 - Connected fully. No error messages.1 - A message fault occurred.2 - Devices are married. Target is identi-fied and correct.3 - A basic connection is established.4033 253 R/W Motor CtrlCom Idle ActDisableWhen this value is TRUE the motor statewill be unchanged after a communicationidle event. A FALSE value will cause theMotor Control Communication Idle Valueto be applied on a com idle event.4049 254 R/W Motor CtrlCom IdleAction ValAction to execute when a communicationidle event occurs.0 = Ignore (No Change)1 = Stop- 255 R/W EtherNet/IPComm Timeout EtherNet/IP communication timeoutRange: 0–60,000 msDefault: 3000 ms- 256 R/W EncapsulationInactivityTimeoutNumber of seconds of inactivity beforeTCP connection is closed