manuals
database
Your AI-powered manual search engine
Search
Home
Brands
Genie
Lifting Systems
GTH-4013 SX
Genie GTH-4013 sx Service Manual
Print this manual
Download
Genie GTH-4013 sx Service Manual
Also see for GTH-4013 SX:
Operator's manual
Table of content
Contents
Table Of Contents
Table Of Contents
Table Of Contents
Main dimensions
Tyres
Forks (floating type)
Machine sounds level
Tightening torques
Drill diameters for threads
Locking material
Hoisting instructions
Advice to renew flexible hoses
Machine paint colour
Checking the cylinder movement times
Hydraulic settings
Check transmission piloting
DLE system
About this section
Maintenance table
Maintenance inspection report
Introduction
Table A procedures
A-2 Check the tightening of the wheel bolts
A-3 Check the tightening of all bolts and nuts
A-5 Inspect the Operator's Manual
A-7 Check the engine oil level
A-8 Clean the air suction filter
A-9 Check and clean the radiator
A-10 Check the hydraulic oil level in the tank
A-11 Check the greasing of the boom section pads
A-12 Grease the forks
the transmission shafts, the front and rear axles and any equipment of the machine
A-14 Check the efficency of the lighting electric system
A-16 Check the efficency of the steering selection system
A-17 Check the efficency of the fork balancing system
A-18 Check the efficient working order of the safety devices
A-19 Check the engine coolant level
A-20 Check the efficency of the overload warning system
A-21 Check the re-sequence of the boom telescope (GTH 4013sx)
Table B procedures
B-3 Check the tyre inflation
B-4 Check the tightening of the wheel nuts
B-5 Check the tightening of the cardan shaft screws
B-6 Clean the radiator fins
Table C procedures
C-2 Change the engine oil and relevant filter
C-3 Check the oil level in the front and rear differential gears
C-5 Check and clean the engine air filter
C-6 Check the clamping of the cableheads to the battery terminals
C-8 Check the cylinder chromium-plated rods
C-10 Check the electric cables
C-12 Adjust the play of the sliding pads of the boom sections
C-13 Grease the sliding parts of the boom sections
C-14 Check the level of the battery electrolyte
C-15 Check the efficency of the block valves
Courtesy of Crane.Market
Table D procedures
D-3 Check the tightening of the cab fixing screws
D-5 Change the hydraulic oil filter cartridge
D-6 Have the hydraulic system checked by a skilled technician
D-8 Change the engine oil filter and the fuel filter
D-10 Change the oil of the front and rear differential gears
Table E procedures
E-2 Change the oil in the power divider gears
E-4 Change the hydraulic oil and the inner hydraulic oil filter
Table F procedures
G-1 Check the machine structure
Electrical faults
Hydraulic faults
Hydraulic symbols
GTH-4013 SX
GTH-4017 SX
Electrical schemes
Fuses and relays GTH-4013 SX GTH-4017 SX
Time schedule
Removing the engine from the machine
Hydraulic pumps disassembly
Disassembling the hydraulic motor
Water-oil cooler disassembly
Main valve disassembly
Renewing the slide pads of the telescopic boom GTH 4013 SX
Renewing the slide pads of the telescopic boom GTH 4017 SX
Renewing the flexible hoses inside the boom GTH 4013 SX
Renewing the flexible hoses inside the boom GTH 4017 SX
16
GTH-4013 SX GTH-4017 SX
Document 57.4403.4200
Section 2 - Technical Specification
May 2008
TECHNICAL
SPECIFICATION
OUTRIGGERS CONTROL
MACHINE SWAY
GTH 4013 SX
Time (s)
Up
Down
Max engine speed
6”
7”
Min engine speed
14”
19”
GTH 4013 SX
Time (s)
from right to left - from left to right
Max engine speed
13”
12”
Min engine speed
17”
17”
Lift
Lower
Courtesy of Crane.Market
Previous
Next
/ 202
Zoom view
Related manuals for Genie GTH-4013 SX
Genie S-40 Service Manual
Genie S-40 Service Manual
Genie GTH-1048 Service Manual
Genie GR-8 Service Manual
Genie S-80 Service Manual
Genie S-65 Service Manual
Genie S-60 Service Manual
Genie S-65 Service Manual
Genie GTH-4013 SX Operator's Manual
Genie GR-12 Service Manual
This manual is suitable for:
GTH-4013 SX
GTH-4017 SX
manuals
database
Your AI-powered manual search engine
