Panasonic AJ-HPX2700G Operating Instructions Manual

Contents

22 Parts and their Functions: Shooting and Recording/Playback Functions Section30. DVCPRO connectorThis is an output connector for video, audio, and datathat comply with the IEEE1394 standard.¡Notesy Power is not supplied from the unit.y Be absolutely sure to bear the following points in mindwhen connecting the IEEE1394 cable (DV cable).– Ensure that the connections with other devices aremade on a 1:1 basis.– When a 1394 cable (DV cable) has been connectedto the DVCPRO connector, do not apply any strongexternal force as this may damage the connector.– When error code 1394 E-92 (1394 INITIALERROR) appears, disconnect the connectingcables and re-connect them or turn off the unit’spower and turn it back on.– Ensure that the unit and all of the connecteddevices are each grounded (or connected to acommon ground) before use.If it is not possible to ground the unit and devices,turn off the power of the unit and of all theconnected devices before connecting ordisconnecting the IEEE1394 cable.– When the unit is to be connected to a deviceequipped with a 4-pin type of connector, connectthe unit’s connector (6-pin type) first.– When connecting the unit with a PC equipped witha 6-pin type of connector, connect the 1394 cableas dictated by the shapes of the 1394 connectors.Bear in mind that inserting a plug the wrong wayround may damage the unit.– When the unit is used in AVC-Intra format, image/audio signals cannot be output through theDVCPRO connector.31. REMOTE (remote control) connectorThe remote control unit AJ-RC10G (optional) isconnected here.32. Option slotAttach the video encoder card (AJ-YAX800G, optional).For information about the installation and proxyrecording, see the AJ-YAX800G instruction manual.33. SD memory card insertion slotAn SD memory card (optional) is inserted here. SDmemory cards are used for recording and accessing themenu settings of cameras and the lens files, uploadingmetadata, and proxy recording (optional).Use the unit by inserting an SD memory card that iscompliant with the SD standard or the SDHC standard.MultiMediaCards cannot be used. (Bear in mind thatrecording may no longer be possible if you do usethem.)If you intend to use miniSD cards in unit, always installthe adapter specially designed for miniSD cards. (Theunit will not work properly if only the miniSD cardadapter is installed. Make sure that the card has beeninstalled in the adapter before using it.)Use of Panasonic’s SD memory cards and miniSDcards is recommended. Be sure to format cards usingunit.Any SD memory card and SDHC memory card with thefollowing capacities can be used with the unit.To record proxy (optional), use an SD memory card witha capacity of 256 MB, 512 MB, 1 GB, or 2 GB labeled“High Speed” or use an SDHC memory card.For the latest information not available in the operatinginstructions, visit the P2 Support Desk at the followingWeb site.34. Busy (operation mode display) lampThis lamp indicates the active status of the SD memorycard.It stays illuminated when the card is active.¡NoteWhile the lamp is on, do not insert or remove the card.6-pin type 4-pin typeSD memory card8 MB, 16 MB, 32 MB, 64 MB,128 MB, 256 MB, 512 MB, 1 GB,2 GBSDHC memory card 4 GB, 8 GB, 16 GB, 32 GBhttps://eww.pavc.panasonic.co.jp/pro-av/y The SDHC card conforms to a new standard for memorycards with a large capacity of more than 2 GB whichwas established by the SD Association in 2006.y The SD card logo is a registered trademark.y MMC (MultiMediaCard) is a registered trademark ofInfineon Technologies AG.