Panasonic AJ-HPX2700G Operating Instructions Manual

Contents

78 Adjustments and Settings for Recording: Viewfinder Screen Status DisplaysInformation Item Indication Status11. Camera Warningand Report AreaAWB A ACTIVEAWB B ACTIVEAWB A OK ½.½KAWB B OK ½.½KAWB BREAK ½.½KAWB NGCOLOR TEMP LOWCOLOR TEMP HIGHLEVEL OVERLOW LIGHTTIME OVERAWB PRESET ½.½KCHECK FILTERABB ACTIVEABB OKABB BREAKABB NGB-SHD READYB-SHD ACTIVEB-SHD OKB-SHD BREAKB-SHD NGAWB being performed on Ch A.AWB being performed on Ch B.AWB successful on Ch A.AWB successful on Ch B.AWB action aborted by user.AWB action failed. The second line indicates the status.Color temperature too low.Color temperature too high.Brightness too high.Brightness too low.Action timed-out.AWB cannot be performed because the AWB switch is position at [PRST] orthe super gain is enabled.Make sure the FILTER control is positioned correctly.ABB being performed.ABB action successful.ABB action aborted by user.ABB action failed.Black shading accepted (by holding down the ABB switch during ABBadjustment).Black shading being adjusted.Black shading adjustment successful.Black shading adjustment aborted by user.Black shading adjustment failed.(Related to AWB, ABBand switch settings)(Switch changeoverindication)WHITE: # ½.½KAUTO KNEE: ON/OFFGAIN: ½½dBSS: 1/½½½½, ½½½.½d,X½½½.½dSS: X 1/½½½½, XX1/½½½ND: ½/CC: ½½KEXTENDER: ON/OFF/½½KIRIS: ½½ F ½.½DRS: ON/OFFThe WHITE BAL switch has been switched. # is replaced with A, B or PRE.AUTO KNEE switch has been switched to [ON] or [OFF].Gain has been switched with the GAIN selector switch or a user button.When the shutter speed has been switched, the shutter speed is indicated.Shutter speed is in SYNCHRO SCAN mode.This appears when the filter setting has been selected.Lens extender has been turned on or off.Indicated when the iris override correction value is to be changed.The dynamic range stretcher has been switched.(Low light warning) LOW LIGHT Brightness too low.(Y GET value) ½½½.½% With the Y GET ON setting, the output brightness level near the center markeris displayed as “%”.12. User buttonfunctionsINHI.OVR ON/OFFS.BLK –½½/OFFB.GAMMA ON/OFFY GET ON/OFFDRS ON/OFFASSIST ON/OFFC.TEMP ON/OFFVFR ON/OFFFRATE ON/OFFVF GAM ON/OFFAUDIO CH1AUDIO CH2REC SWRET SWPRE RECSLOT SELUSB HOST/DEVICE/OFFVF MARK A/B/OFFTEXT MEMOUser buttons disabled.Iris override can be set (the iris override setting is on).Status of super black (on or off). When it is on, the set value is also indicated.Status of black gamma (shade correction for the black level): on or offIndicates whether the Y GET function is on or off.Indicates whether the dynamic range stretcher function is on or off.Indicates whether the focus assist function is on or off.Indicates the mode for changing the color temperature with the jog dial buttonis on or off.Indicates whether the VFR function is on or off.Indicates whether the frame rate set in USR SW F.RATE is being applied.Indicates whether the monitor gamma function is enabled for the viewfinder.Input signal to be recorded on audio channel 1 has been switched.Input signal to be recorded on audio channel 2 has been switched.User button acts as REC switch.User button acts as RET switch.Indicates that PRE RECORDING mode has been switched on or off.Switch that changes the target card is set.USB action status has been switched.Displayed when the marker displayed in the viewfinder and on the LCD screenhas been changed.Indicates whether the TEXT MEMO function is on or off.UM:U1:U2:U3:U4:USER MAINbuttonUSER 1 buttonUSER 2 buttonMARKERSELECT buttonTEXT MEMObutton