Yamaha pmn Owner's Manual

Also see for CinemaDSP digital RX-Z1: Owner's manual Service manual

Contents

E-21PREPARATIONS EnglishCONNECTIONSConnecting video componentsBefore you connect any components, disconnect the power supply to all the components you plan to connect including this unit and deter-mine which jacks are for the left and right channels and for input and output. After you finish all connections, check them again to make surethey are correct. About the video jacksThere are three types of video jacks.IMPEDANCE SELECTORSET BEFORE POWER ONSELECTEUR D’IMPEDANCESPEAKERSR LFRONTRR LLREARCENTERMAINB R LAREAR CENTER(SURROUND)CAUTION SEE INSTRUCTION MANUAL FOR CORRECT SETTING.ATTENTION POUR UN REGLAGE CORRECT, SE REPORTER AU MANUEL D’INSTRUCTIONS.AUDIOAUDIODIGITALZONE 2 OUTDIGITALFRONTINFRONTOUTREAR(SURROUND)SUBWOOFERSPLITMONOREAR CTRINOUTREMOTE 1INCTRLOUT+12V 10mAMAX.RS–232CREMOTE 2CENTERINCENTEROUTR LPREOUT/MAIN INCONTROLMAININMAINOUTR LPHONOGNDCDLRR LVIDEO6CH INPUT CENTERSUBWOOFERVCR 3/DVRLSURROUNDMAINR1CD–RIN(PLAY)3OUT(REC)4MD/TAPEIN(PLAY)3OUT(REC)4OPTICALINOPTICALOUTCOAXIALINwD–TV/LD0MD/TAPE6SATqDVD9CD–R8CD7CD–R5CABLE4DVD3CD2LDLDRF(AC–3)1FRONTREARREAR CENTERCENTERMAIN A OR BA + B: 6ΩMIN. /SPEAKER: 4ΩMIN. /SPEAKER: 4ΩMIN. /SPEAKER: 4ΩMIN. /SPEAKER: 4ΩMIN. /SPEAKER: 8ΩMIN. /SPEAKERFRONTREARREAR CENTERCENTERMAIN A OR BA + B: 8ΩMIN. /SPEAKER: 8ΩMIN. /SPEAKER: 8ΩMIN. /SPEAKER: 8ΩMIN. /SPEAKER: 8ΩMIN. /SPEAKER: 16ΩMIN. /SPEAKERTUNERFM ANT75ΩUNBAL.AMANT–GNDAC OUTLETSAC INSWITCHED100W MAX. TOTAL1.0A MAX. TOTAL120V 60HzVIDEOVIDEODVDS VIDEOCABLESATINVCR 1OUTINVCR 2OUTD–TV/LDOUT1MONITOROUT2INVCR 3/DVRA DVDCOMPONENT VIDEOB D–TV/LDC SATMONITOROUTY PB/CB PR/CR1 2 31 Composite VIDEO jackVideo signals input through the VIDEO jacks are the conventionalcomposite video signals.2 S VIDEO jackVideo signals input through the S VIDEO jacks are separated intoluminance (Y) and color (C) video signals. The S-video signalsachieve high quality color reproduction. When you are using the SVIDEO jacks, check the details in the owner’s manual that camewith the component being connected.3 COMPONENT VIDEO jacksVideo signals input through the COMPONENT VIDEO jacks areseparated into luminance (Y) and color difference (PB /C B, PR/C R )video signals. The jacks are also separated into three for each signal.The labels of the component video jacks may be different depend-ing on the component (e.g. Y, C B, C R / Y, P B, PR / Y, B-Y, R-Y/ etc.).Component video signals provide the best quality in picturereproduction. When you are using the COMPONENT VIDEOjacks, check the details in the owner’s manual that came with thecomponent being connected.Cautions• Use a commercially available S-video cable when connecting tothe S VIDEO jacks, and commercially available video cableswhen connecting to the COMPONENT VIDEO jacks.• Each type of video jack works independently. Signals inputthrough the composite video, S-video, and component jacks areoutput through the corresponding composite video, S-video, andcomponent jacks respectively.• If your video monitor is connected only to the COMPONENTVIDEO jacks of this unit, the OSD is not shown.Note• You can designate the input for the COMPONENT VIDEO A, Band C jacks according to your component by using “8 I/OASSIGNMENT” on the SET MENU (see page __ for details).