Contents - Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Section 1 Introduction
- Product documentation
- Document revision history
- Related documents
- Document conventions
- IEC 61850 edition 1 / edition 2 mapping
- Section 2 Application
- Wide area measurement functions
- Back-up protection functions
- Control and monitoring functions
- Communication
- Basic IED functions
- Section 3 Configuration
- Description of configuration RES670
- Description of configuration B20
- Section 4 Analog inputs
- Setting of the phase reference channel
- Example 1
- Example 3
- Examples on how to connect, configure and set CT inputs for most commonly used CT connections
- Example on how to connect a star connected three phase CT set to the IED
- Example how to connect single-phase CT to the IED
- Relationships between setting parameter Base Current, CT rated primary current and minimum pickup of a protection IED
- Examples how to connect, configure and set VT inputs for most commonly used VT connections
- Examples on how to connect a three phase-to-earth connected VT to the IED
- Example on how to connect a phase-to-phase connected VT to the IED
- Example on how to connect an open delta VT to the IED for high impedance earthed or unearthed networks
- for low impedance earthed or solidly earthed power systems
- Section 5 Local HMI
- Display
- LEDs
- Keypad
- Local HMI functionality
- Parameter management
- Front communication
- Protocol reporting via IEEE 1344 and C37.118 PMUREPORT
- Operation principle
- Frequency reporting
- Reporting filters
- Scaling Factors for ANALOGREPORT channels
- PMU Report Function Blocks Connection Rules in PCM600 Application Configuration Tool (ACT)
- Setting guidelines
- Power swing detection ZMRPSB
- Basic characteristics
- Out-of-step protection OOSPPAM
- Directional phase overcurrent protection, four steps OC4PTOC
- Settings for each step
- Setting example
- Directional residual overcurrent protection, four steps EF4PTOC
- Common settings for all steps
- nd harmonic restrain
- Parallel transformer inrush current logic
- Settings for each step (x = 1, 2, 3 and 4)
- Four step directional negative phase sequence overcurrent protection NS4PTOC
- Sensitive directional residual overcurrent and power protection SDEPSDE
- Identification
- Thermal overload protection, one time constant, Celsius Fahrenheit LCPTTR/LFPTTR
- Setting guideline
- Directional underpower protection GUPPDUP
- Directional overpower protection GOPPDOP
- Two step undervoltage protection UV2PTUV
- Settings for two step undervoltage protection
- Two step overvoltage protection OV2PTOV
- Application
- Equipment protection, such as for motors, generators reactors and transformers
- Underfrequency protection SAPTUF
- Overfrequency protection SAPTOF
- Rate-of-change of frequency protection SAPFRC
- Frequency time accumulation protection function FTAQFVR
- Section 11 Multipurpose protection
- Current and voltage selection for CVGAPC function
- Base quantities for CVGAPC function
- Inadvertent generator energization
- Negative sequence overcurrent protection
- Generator stator overload protection in accordance with IEC or ANSI standards
- generators and circuit breaker head flashover protection for generators
- Voltage restrained overcurrent protection for generator and step-up transformer
- Loss of excitation protection for a generator
- Section 12 System protection and control
- Section 13 Secondary system supervision
- Fuse failure supervision FUFSPVC
- Negative sequence based
- Zero sequence based
- Dead line detection
- Section 14 Control
- Tripping logic SMPPTRC
- Three-phase tripping
- Single- and/or three-phase tripping
- Single-, two- or three-phase tripping
- Example of directional data
- Blocking of the function block
- Logic for group alarm ALMCALH
- Logic for group indication INDCALH
- Fixed signal function block FXDSIGN
- Boolean 16 to Integer conversion B16I
- Boolean to integer conversion with logical node representation, 16 bit BTIGAPC
- Integer to Boolean 16 conversion IB16
- representation ITBGAPC
- Elapsed time integrator with limit transgression and overflow supervision TEIGAPC
- Comparator for real inputs - REALCOMP
- Measurement
- Zero clamping
- Setting examples
- Gas medium supervision SSIMG
- Liquid medium supervision SSIML
- Breaker monitoring SSCBR
- Event function EVENT
- Disturbance report DRPRDRE
- Recording times
- Binary input signals
- Analog input signals
- Consideration
- Logical signal status report BINSTATREP
- Running hour-meter TEILGAPC
- Pulse-counter logic PCFCNT
- Function for energy calculation and demand handling ETPMMTR
- Access point
- Redundant communication
- Merging unit
- Communication protocols
- Receiving data
- IEC/UCA 61850-9-2LE communication protocol
- Specific settings related to the IEC/UCA 61850-9-2LE communication
- Setting examples for IEC/UCA 61850-9-2LE and time synchronization
- IEC 61850 quality expander QUALEXP
- LON communication protocol
- MULTICMDRCV and MULTICMDSND
- IEC 60870-5-103 communication protocol
- Design
- Settings
- Settings for RS485 and optical serial communication
- Settings from PCM600
- Function and information types
- DNP3 Communication protocol
- Binary signal transfer
- Communication hardware solutions
- Authority status ATHSTAT
- Change lock CHNGLCK
- Denial of service SCHLCCH/RCHLCCH
- IED identifiers TERMINALID
- Factory defined settings
- Frequency values
- Test mode functionality TESTMODE
- Process bus IEC/UCA 61850-9-2LE synchronization
- Current transformer requirements
- Conditions
- Fault current
- General current transformer requirements
- PX, PXR (and old IEC 60044-6, class TPS and old British Standard, class X)
- Voltage transformer requirements
- PTP requirements
- IEC/UCA 61850-9-2LE Merging unit requirements
- Application manual
- Section 24 Glossary
|
IEC 61850 quality expander QUALEXP.................................... 307LON communication protocol......................................................... 308Application................................................................................. 308MULTICMDRCV and MULTICMDSND..................................... 309Identification......................................................................... 310Application............................................................................310Setting guidelines................................................................. 310SPA communication protocol......................................................... 310Application................................................................................. 310Setting guidelines...................................................................... 311IEC 60870-5-103 communication protocol..................................... 313Application................................................................................. 313Functionality......................................................................... 313Design.................................................................................. 314Settings......................................................................................316Settings for RS485 and optical serial communication.......... 317Settings from PCM600......................................................... 318Function and information types................................................. 320DNP3 Communication protocol...................................................... 321Application................................................................................. 321Section 20 Remote communication................................................323Binary signal transfer......................................................................323Identification.............................................................................. 323Application................................................................................. 323Communication hardware solutions..................................... 324Setting guidelines...................................................................... 325Section 21 Security........................................................................ 331Authority status ATHSTAT............................................................. 331Application................................................................................. 331Self supervision with internal event list INTERRSIG...................... 331Application................................................................................. 331Change lock CHNGLCK................................................................. 332Application................................................................................. 332Denial of service SCHLCCH/RCHLCCH ....................................... 333Application................................................................................. 333Setting guidelines...................................................................... 333Section 22 Basic IED functions...................................................... 335IED identifiers TERMINALID.......................................................... 335Application................................................................................. 335Product information PRODINF....................................................... 335Application................................................................................. 335Table of contents10 Phasor measurement unit RES670 2.2 IECApplication manual
|
