GE B30 Instruction Manual

Also see for b30: Maintenance manual Instruction manual Instruction manual Instruction manual Communications manual

Contents

x B30 BUS DIFFERENTIAL SYSTEM – INSTRUCTION MANUALINDEXPortEthernet, turn on or off .................................................................. 5-44failure monitoring ............................................................................ 5-37HTTP, close .......................................................................................... 5-99IEC 60870-5-104, close ...............................................................5-101Modbus, close .................................................................................... 5-50on rear panel ..................................................................................... 3-12SNTP, close ........................................................................................5-112TFTP, close .........................................................................................5-100USB ......................................................................................................... 4-16Port numbercombinations with protocols ...................................................... 5-50connectivity report of those used ............................................ 4-76DNP ......................................................................................................... 5-51HTTP ....................................................................................................... 5-99IEC 60870-5-104 ............................................................................5-100list of ....................................................................................................... 5-44Modbus ................................................................................................. 5-49Modbus during installation ......................................................... 3-64RADIUS .................................................................................................. 5-18SNTP .....................................................................................................5-112system log ............................................................................... 5-18, 5-19TFTP ......................................................................................................5-100Power meteringspecifications ..................................................................................... 2-25values .................................................................................................... 6-18Power off, save data first ............................................................... 3-16Power supplydescription .......................................................................................... 3-15diagram ................................................................................................ 3-12LED on module .................................................................................. 3-16removal to replace battery .......................................................10-24specifications ..................................................................................... 2-27wire size ................................................................................................ 3-15Power system settings ...................................................................5-144Precision Time Protocolactual values for port state ............................................................ 6-8clock settings ...................................................................................5-109error message ...................................................................................... 7-8port behavior ..................................................................................... 5-45settings ...............................................................................................5-110specifications ..................................................................................... 2-30Preferencescomparing settings ......................................................................... 10-7Engineer ............................................................................................... 4-76IEC 61850 ............................................................................................. 5-60import file ............................................................................................ 10-9Preserve custom attributes when importing SCD/CID files .10-9Print front panel labels ........................................................ 4-43, 4-75Process busorder codes for compatible URs .................................................. 2-8overview ............................................................................................... 3-18Product informationactual values ...................................................................................... 6-26Device Connectivity Report in Engineer ................................ 4-76firmware revision ............................................................................. 6-26Programmed mode ........................................................................... 3-52Protection elements .............................................................................5-4Protection Summary interface ............................ 3-67, 4-4, 5-227Protocol selection ............................................................................... 5-50Prototype firmware error message .......................................... 7-11PRPactual values ...................................................................................... 6-11explained .............................................................................................. 5-46settings .................................................................................................. 5-44specifications ..................................................................................... 2-31PTPactual values for port state ............................................................6-8clock settings .................................................................................. 5-109error message ......................................................................................7-8port behavior ...................................................................................... 5-45settings ............................................................................................... 5-110specifications ..................................................................................... 2-30pu quantity .................................................................................................5-4Pushbuttonscontrol FlexLogic ........................................................................... 5-169control logic diagram .................................................................. 5-125control settings .............................................................................. 5-124control specifications ..................................................................... 2-23testing .......................................................................................................7-3user-programmable FlexLogic ............................................... 5-176user-programmable logic diagrams .................................... 5-130user-programmable settings .................................................. 5-126user-programmable specifications ......................................... 2-24QQuick Connect ........................................................................... 3-67, 3-68RRADIUS serverauthentication ................................................................................... 5-15setup .........................................................................................................B-1RAM required ......................................................................................... 3-54Reactive power ..................................................................................... 6-18Reactive power specifications ..................................................... 2-25Real power .............................................................................................. 6-18Real-time clockactual values for synchronization ...............................................6-8settings ............................................................................................... 5-109Reboot relayusing EnerVista .....................................................................................5-1using relay ..............................................................................................7-3Recloser curves ...................................................................5-161, 5-199RedundancyPRP actual values ............................................................................. 6-11PRP explained .................................................................................... 5-46settings .................................................................................................. 5-44specifications ..................................................................................... 2-31Relay architecture ........................................................................... 5-166Relay maintenance ...............................................................................7-3Relay name .......................................................................................... 5-141Release Notes ..................................................................................... 10-14