417 SCAN OPERATION Scan start/stopD PreparationScan resume condition (p. 45); program the scan edges(pgs. 42, 43); program 2 or more memory channels (pgs. 30,31); set skip settings, if desired (p. 44).D Operationq Select VFO mode for full/programmed scan with[V/MHz•SCAN]; or memory mode for memory scan with[M/CALL•MW] in the desired band.• Select the desired bank with the same band’s [MAIN•BAND] forbank scan.w Set the squelch to the point where noise is just muted.e Push the [V/MHz•SCAN] for 1 sec. to start the scan.• To change the scanning direction, rotate the same band’s [DIAL].• The memory channel readout blinks the scan type as follows:r Push [SET• ] to switch full and programmed scan (P1,P2, P3, P4 and P5), if VFO is selected in step q.t To stop the scan, push the [V/MHz•SCAN].z Push [VFO/LOCK] to select VFO mode forfull/programmed scan; push [MR/CALL] to selectmemory mode for memory scan, in the mainband.• Push [FUNC] then [ MONI 1(BANK)] to select a bankfor bank scan.x Push [ SQLY D(MUTE)] or [ SQLZ #(16KEY-L)] toset the squelch to the point where noise is justmuted.c Push [SCAN 2(T-SCAN)] to start the scan.• Push [Y] or [Z] for 1 sec. also starts the scan.v Push [ SET B(D-OFF)] to switch full and pro-grammed scan (P1, P2, P3, P4 and P5), if VFOis selected in step z.b To stop the scan push [ SCAN 2(T-SCAN)] or[CLR A(MW)].SCAN2SETBMAINT XMMAINT XMMAINT XMMAINT XM• During full scan • During programmed scan • During memory scan • During bank scanIndicates scan edge channels.• P1 stands for 1A/1b• P1 to P5 are available when theyare programmed, and switcheswith [SET• ].Indicates bank initial.Push [SET• ] to select “AL”(full) or programmed scan (P1,P2, P3, P4 and P5) insequence.

quick reference guide

using the mounting bracket

battery connection

antenna installation

i repeater operation

I Front panel— controller

panel description

I Function display

main unit

I Microphone (HM-133)

I Microphone keypad

I Optional microphones (HM-118N/TN/TAN)

I Preparation

setting a frequency

I Using the tuning dial

I Tuning step selection

I Lock functions

I Receiving

I Squelch attenuator

I V/V, U/U simultaneous receive (Para-watch)

I Sub band mute/sub band busy beep

I Transmitting

I One-touch PTT function

I General

I Accessing a repeater

repeater operation

I Subaudible tones

I Offset frequency

I General description

I Programming a memory channel

programming a memory channel via the microphone

I Transferring memory contents

memory operation

I Memory clearing

I Memory bank selection

I Memory bank setting

I Transferring bank contents

I Call channel selection

I Programming a call channel

I Scan types

I Scan start/stop

I Scan edges programming

scan operation

I Skip channel setting

I Scan resume condition

I Priority watch types

I Priority watch operation

I Programming a DTMF code

dtmf memory encoder

i transmitting a dtmf code

I DTMF speed

I Pocket beep operation

tone scan

other functions

I Initial set mode

I AM/FM narrow mode

i weather channel operation

I Microphone keys

I Packet operation

I Troubleshooting

I Fuse replacement

I Speciﬁcations

I Options

mode arrangement

Icom IC-2720H Instruction Manual

IC-2720

IC-2720H