305MEMORY OPERATION5 Programming channel namesEach memory channel and the call channel can be pro-grammed with an alphanumeric channel name for easyrecognition and can be indicated independently by channel.Names can be a maximum of 6 characters— see the tablebelow for available characters.q Push [M/CALL(PRIO)] to select memory mode.w Rotate the tuning dial to select the desired memory channel.e Push [MONI(ANM)] for 1 sec. to select channel name in-dication mode.• 1 short and 1 long beep sound.r Push [SET(LOCK)] to select the channel name program-ming condition.• Frequency readouts disappear.t Rotate the tuning dial to select the desired character.• The selected character blinks.y Push [SET(LOCK)] or [MW(S.MW)] to move the cursor toleft or right, respectively.u Repeat steps t and y until the desired channel namesare displayed.i Push [V/MHz(SCAN)] to program the name and exit thechannel name programming condition.o Push [MONI(ANM)] for 1 sec. to return to frequency indi-cation if desired.IMPORTANT!: Once channel name indication mode isselected, always access the channel name programmingcondition when [SET(LOCK)] is pushed.When set mode accessing is necessary, cancel the chan-nel name indication by pushing [MONI(ANM)] for 1 sec.,then access to set mode.(1)(B)(L)(V)(+)(2)(C)( M)( W)(–)(3)( D)(N)(X)(=)(4)(E)(O)(Y)(✱)(5)(F)(P)(Z)(/)(6)(G)( Q)(space)(7)(()( H)( R)())(8)(I)(S)(|)(9)(J)(T)(0)(A)(K )(U)[EXAMPLE]: Programming “CLUB” into memory channel 1.Push .V/MHzSCANSelect memory channel 1,then push for 1 sec.MONIANMPush or to movethe cursor.SETLOCK S.MWMWRotate to select thecharacter. Repeatprevioussteps.

quick reference guide

battery connection

antenna installation

i repeater operation

I Front panel

I Function display

I Rear panel

I Microphone (HM-133V)

I Microphone keypad

I Preparation

I Using the keypad

I Tuning step selection

I Lock functions

I Receiving

I Audio mute function

I Transmitting

I One-touch PTT function

I Accessing a repeater

repeater operation

I Subaudible tones

I Offset frequency

i reversed duplex mode

I Auto repeater

I General description

I Programming a memory channel

programming a memory channel via the microphone

I Transferring memory contents

memory operation

I Memory clearing

i programming channel names

I Memory bank selection

I Memory bank setting

I Transferring bank contents

I Call channel selection

I Programming a call channel

I Scan types

I Scan start/stop

I Scan edges programming

I Skip channel setting

I Scan resume condition

I Priority watch types

I Priority watch operation

I Programming a DTMF code

i transmitting a dtmf code

I DTMF speed

I Pocket beep operation

tone scan

I Code programming

I Pager operation

other functions

I Initial set mode

i weather channel operation

i microphone keys

I Partial reset

I Data cloning

I Troubleshooting

i fuse replacement

I Optional unit installation

specifications and options

mode arrangement

Icom IC-V8000 Instruction Manual

RECEIVER CIRCUITS

MAIN UNIT

PLL CIRCUITS

HM-133V

LOGIC BOARD

IC-V8000

ANI FUNCTION

Preparation

Operation

voice scrambler

explicit definitions

panel description

i function display

i rear panel

i microphone keypad

using the mounting bracket

i battery connection

i antenna installation

setting a frequency

i using the keypad

i tuning step selection

i lock functions

basic operation

i audio mute function

i selecting output power

subaudible tones

d frequency range and offset direction

repeater lockout

i programming a memory channel

i programming a memory channel via the microphone

i transferring memory contents

i memory clearing

i memory bank selection

i memory bank setting

call channel operation

i programming a call channel

scan operation

i scan edges programming

i skip channel setting

i scan resume condition

priority watch

i priority watch operation

dtmf memory encoder

transmitting a dtmf code

i dtmf speed

pocket beep and tone squelch