6712 OTHER FUNCTIONS Microphone keysThe supplied HM-133V’s (optional for some versions) [F-1]and [F-2] keys memorize the transceiver conditions.The [UP]/[DN] keys of the standard or an optional microphone(other than the HM-133V) can be assigned functions like thefunction keys on the transceiver’s front panel.DD [F-1]/[F-2] keys on HM-133VThe following conditions can be memorized into [F-1] and[F-2] keys, independently.• Operating frequency• Repeater setting (offset direction and frequency, toneON/OFF and frequency)• Tone/DTCS squelch (ON/OFF, frequency/code and polarity)• Transmit output power selection• Set mode settings• Initial set mode settings (except display type item)➥ Programming the conditionSet the desired contents of each condition,then push [F-1]/[F-2] for 1 sec.• 3 beeps sound.➥ Re-calling the conditionPush [F-1]/[F-2] momentarily.DD [UP]/[DN] keys on a microphones(other than HM-133V)The following functions are assigned to the [UP]/[DN] keys onthe other microphones (HM-118N/TAN, etc.) when first apply-ing power.[UP] : channel up; push and hold to start scan, push againto stop scan.[DN] : channel down; push and hold to start scan, pushagain to stop scan.➥ Assigning a functionq Turn the power OFF.w While pushing the desired switch on the transceiver andone of either [UP]/[DN] keys on the microphone, turn thepower ON.• The function is programmed into the key.➥ Clearing an assignmentq Turn the power OFF.w While pushing the desired [UP] or [DN] key on the micro-phone, turn the power ON.AT POWER ON[F-1]/[F-2]

quick reference guide

battery connection

antenna installation

i repeater operation

I Front panel

I Function display

I Rear panel

I Microphone (HM-133V)

I Microphone keypad

I Preparation

I Using the keypad

I Tuning step selection

I Lock functions

I Receiving

I Audio mute function

I Transmitting

I One-touch PTT function

I Accessing a repeater

repeater operation

I Subaudible tones

I Offset frequency

i reversed duplex mode

I Auto repeater

I General description

I Programming a memory channel

programming a memory channel via the microphone

I Transferring memory contents

memory operation

I Memory clearing

i programming channel names

I Memory bank selection

I Memory bank setting

I Transferring bank contents

I Call channel selection

I Programming a call channel

I Scan types

I Scan start/stop

I Scan edges programming

I Skip channel setting

I Scan resume condition

I Priority watch types

I Priority watch operation

I Programming a DTMF code

i transmitting a dtmf code

I DTMF speed

I Pocket beep operation

tone scan

I Code programming

I Pager operation

other functions

I Initial set mode

i weather channel operation

i microphone keys

I Partial reset

I Data cloning

I Troubleshooting

i fuse replacement

I Optional unit installation

specifications and options

mode arrangement

Icom IC-V8000 Instruction Manual

RECEIVER CIRCUITS

MAIN UNIT

PLL CIRCUITS

HM-133V

LOGIC BOARD

IC-V8000

ANI FUNCTION

Preparation

Operation

voice scrambler

explicit definitions

panel description

i function display

i rear panel

i microphone keypad

using the mounting bracket

i battery connection

i antenna installation

setting a frequency

i using the keypad

i tuning step selection

i lock functions

basic operation

i audio mute function

i selecting output power

subaudible tones

d frequency range and offset direction

repeater lockout

i programming a memory channel

i programming a memory channel via the microphone

i transferring memory contents

i memory clearing

i memory bank selection

i memory bank setting

call channel operation

i programming a call channel

scan operation

i scan edges programming

i skip channel setting

i scan resume condition

priority watch

i priority watch operation

dtmf memory encoder

transmitting a dtmf code

i dtmf speed

pocket beep and tone squelch