448PRIORITY WATCH8 Priority watch operationq Select VFO mode; then, set an operating frequency.w Set the watching channel(s).For memory channel watch:Select the desired memory channel.For memory scan watch:Select memory mode; then, push [V/MHz(SCAN)] for1 sec. to start memory scan.For call channel watch:Select the call channel by pushing [M/CALL(PRIO)] sev-eral times.e Push [M/CALL(PRIO)] for 1 sec. to start the watch.• The transceiver checks the memory or call channel every 5 sec.• The watch resumes according to the selected scan resume con-dition. (p. 42)• While the watch is pausing, pushing [M/CALL(PRIO)] resumesthe watch manually.r Push [M/CALL(PRIO)] while the display shows the mem-ory channel to stop the watch.z Select VFO mode; then, set an operating fre-quency.x Set the watching channel(s).For memory channel watch:Push [MR/CALL] then [Y] or [Z] to select the de-sired memory channel.For memory scan watch:Push [MR/CALL], then push [ SCAN 2] to start thememory scan.For call channel watch:Push [MR/CALL] for 1 sec. to select the callchannel.c Push [PRIO 3(PTT-M)] to start the watch.• The transceiver checks the memory or call channelevery 5 sec.• The watch resumes according to the selected scan re-sume condition. (p. 42)• To resume the watch manually when paused, push[PRIO 3(PTT-M)] or [ CLR A(MW)].v To stop the watch, push [ CLR A(MW)] once (ortwice while watch is paused).PRIO3While pausing or receivinga signal on the memory orcall channel, “PRIO” anddecimal point blink.

quick reference guide

battery connection

antenna installation

i repeater operation

I Front panel

I Function display

I Rear panel

I Microphone (HM-133V)

I Microphone keypad

I Preparation

I Using the keypad

I Tuning step selection

I Lock functions

I Receiving

I Audio mute function

I Transmitting

I One-touch PTT function

I Accessing a repeater

repeater operation

I Subaudible tones

I Offset frequency

i reversed duplex mode

I Auto repeater

I General description

I Programming a memory channel

programming a memory channel via the microphone

I Transferring memory contents

memory operation

I Memory clearing

i programming channel names

I Memory bank selection

I Memory bank setting

I Transferring bank contents

I Call channel selection

I Programming a call channel

I Scan types

I Scan start/stop

I Scan edges programming

I Skip channel setting

I Scan resume condition

I Priority watch types

I Priority watch operation

I Programming a DTMF code

i transmitting a dtmf code

I DTMF speed

I Pocket beep operation

tone scan

I Code programming

I Pager operation

other functions

I Initial set mode

i weather channel operation

i microphone keys

I Partial reset

I Data cloning

I Troubleshooting

i fuse replacement

I Optional unit installation

specifications and options

mode arrangement

Icom IC-V8000 Instruction Manual

RECEIVER CIRCUITS

MAIN UNIT

PLL CIRCUITS

HM-133V

LOGIC BOARD

IC-V8000

ANI FUNCTION

Preparation

Operation

voice scrambler

explicit definitions

panel description

i function display

i rear panel

i microphone keypad

using the mounting bracket

i battery connection

i antenna installation

setting a frequency

i using the keypad

i tuning step selection

i lock functions

basic operation

i audio mute function

i selecting output power

subaudible tones

d frequency range and offset direction

repeater lockout

i programming a memory channel

i programming a memory channel via the microphone

i transferring memory contents

i memory clearing

i memory bank selection

i memory bank setting

call channel operation

i programming a call channel

scan operation

i scan edges programming

i skip channel setting

i scan resume condition

priority watch

i priority watch operation

dtmf memory encoder

transmitting a dtmf code

i dtmf speed

pocket beep and tone squelch