4810POCKET BEEP AND TONE SQUELCH910 Pocket beep operationThis function uses subaudible tones for calling and can beused as a “common pager” to inform you that someone hascalled while you were away from the transceiver.D Waiting for a call from a specific stationq Set the operating frequency.w Push [SET(LOCK)] to enter set mode.e Push [SET(LOCK)] or [MW(S.MW)] several times until “Ct”for tone squelch or “dt” for DTCS squelch appears.r Rotate the tuning dial to select the desired tone squelchfrequency or DTCS code and polarity.t Push [TONE(T-SCAN)] to exit set mode.y Push [TONE(T-SCAN)] several times until “ ” or “ ”are displayed to turn ON the pocket beep with tonesquelch or DTCS squelch, respectively.u When a signal with the matched tone is received, thetransceiver emits beep tones and blinks “ ”.• Beep tones sound for 30 sec. and “ ” blinks. To stop the beepsand blinking manually, push any key. When the beep tones arenot stopped manually, “ ” continues flashing until step i isoperated.i Push [PTT] to answer.• “ ” disappears and cancels the pocket beep function automati-cally.o Push [TONE(T-SCAN)] several times until “ ” or “ ” dis-appears to cancel the tone squelch or DTCS squelch func-tion.Appears when the pocket beepwith tone squelch is activated.Appears when the pocket beepwith DTCS squelch is activated.Push [TONE(T-SCAN)] several times to select the pocket beepfunction with tone squelch or DTCS squelch.Tone squelch frequency setting DTCS code Polarity N: normalI: inversePush [SET(LOCK)] to enter set mode.

quick reference guide

battery connection

antenna installation

i repeater operation

I Front panel

I Function display

I Rear panel

I Microphone (HM-133V)

I Microphone keypad

I Preparation

I Using the keypad

I Tuning step selection

I Lock functions

I Receiving

I Audio mute function

I Transmitting

I One-touch PTT function

I Accessing a repeater

repeater operation

I Subaudible tones

I Offset frequency

i reversed duplex mode

I Auto repeater

I General description

I Programming a memory channel

programming a memory channel via the microphone

I Transferring memory contents

memory operation

I Memory clearing

i programming channel names

I Memory bank selection

I Memory bank setting

I Transferring bank contents

I Call channel selection

I Programming a call channel

I Scan types

I Scan start/stop

I Scan edges programming

I Skip channel setting

I Scan resume condition

I Priority watch types

I Priority watch operation

I Programming a DTMF code

i transmitting a dtmf code

I DTMF speed

I Pocket beep operation

tone scan

I Code programming

I Pager operation

other functions

I Initial set mode

i weather channel operation

i microphone keys

I Partial reset

I Data cloning

I Troubleshooting

i fuse replacement

I Optional unit installation

specifications and options

mode arrangement

Icom IC-V8000 Instruction Manual

RECEIVER CIRCUITS

MAIN UNIT

PLL CIRCUITS

HM-133V

LOGIC BOARD

IC-V8000

ANI FUNCTION

Preparation

Operation

voice scrambler

explicit definitions

panel description

i function display

i rear panel

i microphone keypad

using the mounting bracket

i battery connection

i antenna installation

setting a frequency

i using the keypad

i tuning step selection

i lock functions

basic operation

i audio mute function

i selecting output power

subaudible tones

d frequency range and offset direction

repeater lockout

i programming a memory channel

i programming a memory channel via the microphone

i transferring memory contents

i memory clearing

i memory bank selection

i memory bank setting

call channel operation

i programming a call channel

scan operation

i scan edges programming

i skip channel setting

i scan resume condition

priority watch

i priority watch operation

dtmf memory encoder

transmitting a dtmf code

i dtmf speed

pocket beep and tone squelch