427SCAN OPERATION7 Scan resume conditionThe scan resume condition can be selected as timer or pausescan. The selected resume condition is also used for prioritywatch. (p. 44)q Push [SET(LOCK)] to enter set mode.w Push [SET(LOCK)] or [MW(S.MW)] several times until“SCT” or “SCP” appears as shown above.• When “d” is displayed in place of the 100 MHz digit, cancel theDTMF memory encoder in advance. (p. 46)e Rotate the tuning dial to set the desired timer:• “SCT-15” : Scan pauses 15 sec. while receiving a signal.• “SCT-10” : Scan pauses 10 sec. while receiving a signal.• “SCT-5” : Scan pauses 5 sec. while receiving a signal.• “SCP-2” : Scan pauses until the signal disappears and thenresumes 2 sec. later.r Push [TONE(T-SCAN)] to exit set mode.z Push [SET B(D-OFF)] to enter set mode.x Push [ SET B(D-OFF)] or [ ENT C(T-OFF)] severaltimes until “SCT” or “SCP” appears as shown atleft.c Push [Y] or [Z] to select the scan resume condi-tion.• See item e at left for scan resume condition details.v Push [CLR A(MW)] to exit set mode. NOTE:Set mode cannot be accessed when memory names aredisplayed. To set the scan resume condition, return to fre-quency indication by pushing [MONI(ANM)] on the frontpanel for 1 sec., or push [FUNC] then [MONI 1(ANM)] (HM-133V) to cancel the channel name indication, then set asdescribed on this page.SETBThe display shows that thescan will resume 15 sec.after it stops.USING SET MODE

quick reference guide

battery connection

antenna installation

i repeater operation

I Front panel

I Function display

I Rear panel

I Microphone (HM-133V)

I Microphone keypad

I Preparation

I Using the keypad

I Tuning step selection

I Lock functions

I Receiving

I Audio mute function

I Transmitting

I One-touch PTT function

I Accessing a repeater

repeater operation

I Subaudible tones

I Offset frequency

i reversed duplex mode

I Auto repeater

I General description

I Programming a memory channel

programming a memory channel via the microphone

I Transferring memory contents

memory operation

I Memory clearing

i programming channel names

I Memory bank selection

I Memory bank setting

I Transferring bank contents

I Call channel selection

I Programming a call channel

I Scan types

I Scan start/stop

I Scan edges programming

I Skip channel setting

I Scan resume condition

I Priority watch types

I Priority watch operation

I Programming a DTMF code

i transmitting a dtmf code

I DTMF speed

I Pocket beep operation

tone scan

I Code programming

I Pager operation

other functions

I Initial set mode

i weather channel operation

i microphone keys

I Partial reset

I Data cloning

I Troubleshooting

i fuse replacement

I Optional unit installation

specifications and options

mode arrangement

Icom IC-V8000 Instruction Manual

RECEIVER CIRCUITS

MAIN UNIT

PLL CIRCUITS

HM-133V

LOGIC BOARD

IC-V8000

ANI FUNCTION

Preparation

Operation

voice scrambler

explicit definitions

panel description

i function display

i rear panel

i microphone keypad

using the mounting bracket

i battery connection

i antenna installation

setting a frequency

i using the keypad

i tuning step selection

i lock functions

basic operation

i audio mute function

i selecting output power

subaudible tones

d frequency range and offset direction

repeater lockout

i programming a memory channel

i programming a memory channel via the microphone

i transferring memory contents

i memory clearing

i memory bank selection

i memory bank setting

call channel operation

i programming a call channel

scan operation

i scan edges programming

i skip channel setting

i scan resume condition

priority watch

i priority watch operation

dtmf memory encoder

transmitting a dtmf code

i dtmf speed

pocket beep and tone squelch