387SCAN OPERATION7 Scan start/stopD PreparationScan resume condition (p. 42); program the scan edges(pgs. 39, 40); program 2 or more memory channels (pgs. 25,26); set skip settings, if desired (p. 41).D Operationq Select VFO mode for full/programmed scan with[V/MHz(SCAN)]; or memory mode for memory scan with[M/CALL(PRIO)].• Select the desired bank with [BANK(OPT)] for bank scan.w Set the squelch to the point where noise is just muted.e Push [V/MHz(SCAN)] for 1 sec. to start the scan.• To change the scanning direction, rotate the tuning dial.• The memory channel readout blinks the scan type as follows:r Push [SET(LOCK)] to switch full and programmed scan(P1, P2 and P3).t To stop the scan, push [V/MHz(SCAN)].z Push [VFO/LOCK] to select VFO mode forfull/programmed scan; push [MR/CALL] to selectmemory mode for memory scan.• Push [BANK/OPTION] to select a bank for bankscan.x Set the squelch to the point where noise is justmuted.c Push [SCAN 2(T-SCAN)] to start the scan.• Push [Y] or [Z] for 1 sec. also starts the scan.v Push [ SET B(D-OFF)] to switch full and pro-grammed scan (P1, P2 and P3).b To stop the scan push [ SCAN 2(T-SCAN)] or[CLR A(MW)].SCAN2SETB• During full scan • During programmed scan • During memory scanIndicates scan edge channels.• P1 stands for 1A/1b• P1 to P3 are available when theyare programmed, and switcheswith [SET(LOCK)].Push [SET(LOCK)] to select full orprogrammed scan (P1, P2 andP3) in sequence.

quick reference guide

battery connection

antenna installation

i repeater operation

I Front panel

I Function display

I Rear panel

I Microphone (HM-133V)

I Microphone keypad

I Preparation

I Using the keypad

I Tuning step selection

I Lock functions

I Receiving

I Audio mute function

I Transmitting

I One-touch PTT function

I Accessing a repeater

repeater operation

I Subaudible tones

I Offset frequency

i reversed duplex mode

I Auto repeater

I General description

I Programming a memory channel

programming a memory channel via the microphone

I Transferring memory contents

memory operation

I Memory clearing

i programming channel names

I Memory bank selection

I Memory bank setting

I Transferring bank contents

I Call channel selection

I Programming a call channel

I Scan types

I Scan start/stop

I Scan edges programming

I Skip channel setting

I Scan resume condition

I Priority watch types

I Priority watch operation

I Programming a DTMF code

i transmitting a dtmf code

I DTMF speed

I Pocket beep operation

tone scan

I Code programming

I Pager operation

other functions

I Initial set mode

i weather channel operation

i microphone keys

I Partial reset

I Data cloning

I Troubleshooting

i fuse replacement

I Optional unit installation

specifications and options

mode arrangement

Icom IC-V8000 Instruction Manual

RECEIVER CIRCUITS

MAIN UNIT

PLL CIRCUITS

HM-133V

LOGIC BOARD

IC-V8000

ANI FUNCTION

Preparation

Operation

voice scrambler

explicit definitions

panel description

i function display

i rear panel

i microphone keypad

using the mounting bracket

i battery connection

i antenna installation

setting a frequency

i using the keypad

i tuning step selection

i lock functions

basic operation

i audio mute function

i selecting output power

subaudible tones

d frequency range and offset direction

repeater lockout

i programming a memory channel

i programming a memory channel via the microphone

i transferring memory contents

i memory clearing

i memory bank selection

i memory bank setting

call channel operation

i programming a call channel

scan operation

i scan edges programming

i skip channel setting

i scan resume condition

priority watch

i priority watch operation

dtmf memory encoder

transmitting a dtmf code

i dtmf speed

pocket beep and tone squelch