35CALL CHANNEL OPERATION6 Call channel selection➥ Push [M/CALL(PRIO)] sev-eral times to select the callchannel.• “C” appears instead of mem-ory channel number indication.• Push [M/CALL(PRIO)] once ortwice to select memory mode,or push [V/MHz(SCAN)] to se-lect VFO mode.➥ Push [MR/CALL] for 1 sec. to select the callchannel.• Push [MR/CALL ] to select memory mode, or push[VFO/LOCK] to select VFO mode. Call channel transferringq Push [M/CALL(PRIO)] several times to select the callchannel.• “C” appears.w Push [MW(S.MW)] momentarily, then rotate the tuning dialto select the memory channel to transfer the contents to.• “M” indicator and memory channel number blink.• To transfer to the VFO, push [MW(S.MW)] for 1 sec.e Push [MW(S.MW)] for 1 sec. to transfer when a momen-tary push was used in the previous step.• If channel names have been programmed into the call channel,the names are also transferred.z Push [MR/CALL] for 1 sec. to select the callchannel.x Push [FUNC], [CLR A(MW)] momentarily, thenpush [Y]/[Z] to select the memory channel totransfer the contents to.• To transfer to the VFO, push [FUNC], then push[CLR A(MW)] for 1 sec.c Push [FUNC], then [CLR A(MW)] for 1 sec. totransfer when a momentary push was used inthe previous step.• If channel names have been programmed into thecall channel, the names are also transferred.MR/CALLMW[Y]/[Z]MR/CALLPush [M/CALL(PRIO)] severaltimes to select the call channel.Appears✔INFORMATIONWhen the VFO mode is se-lected from the call channel,a small “c” appears insteadof memory channel number.Small “c” shows VFO wasselected from the call channel.

quick reference guide

battery connection

antenna installation

i repeater operation

I Front panel

I Function display

I Rear panel

I Microphone (HM-133V)

I Microphone keypad

I Preparation

I Using the keypad

I Tuning step selection

I Lock functions

I Receiving

I Audio mute function

I Transmitting

I One-touch PTT function

I Accessing a repeater

repeater operation

I Subaudible tones

I Offset frequency

i reversed duplex mode

I Auto repeater

I General description

I Programming a memory channel

programming a memory channel via the microphone

I Transferring memory contents

memory operation

I Memory clearing

i programming channel names

I Memory bank selection

I Memory bank setting

I Transferring bank contents

I Call channel selection

I Programming a call channel

I Scan types

I Scan start/stop

I Scan edges programming

I Skip channel setting

I Scan resume condition

I Priority watch types

I Priority watch operation

I Programming a DTMF code

i transmitting a dtmf code

I DTMF speed

I Pocket beep operation

tone scan

I Code programming

I Pager operation

other functions

I Initial set mode

i weather channel operation

i microphone keys

I Partial reset

I Data cloning

I Troubleshooting

i fuse replacement

I Optional unit installation

specifications and options

mode arrangement

Icom IC-V8000 Instruction Manual

RECEIVER CIRCUITS

MAIN UNIT

PLL CIRCUITS

HM-133V

LOGIC BOARD

IC-V8000

ANI FUNCTION

Preparation

Operation

voice scrambler

explicit definitions

panel description

i function display

i rear panel

i microphone keypad

using the mounting bracket

i battery connection

i antenna installation

setting a frequency

i using the keypad

i tuning step selection

i lock functions

basic operation

i audio mute function

i selecting output power

subaudible tones

d frequency range and offset direction

repeater lockout

i programming a memory channel

i programming a memory channel via the microphone

i transferring memory contents

i memory clearing

i memory bank selection

i memory bank setting

call channel operation

i programming a call channel

scan operation

i scan edges programming

i skip channel setting

i scan resume condition

priority watch

i priority watch operation

dtmf memory encoder

transmitting a dtmf code

i dtmf speed

pocket beep and tone squelch