Kenwood KDC-PSW9527 Instruction Manual

Also see for KDC-PSW9527: Service manual

Contents

English | 312nd sectionMulti-function key operation Audio setup item[2]"MEMORY"[2] "USER"[3] "INST"User MemoryUser Insttaller[3]"CALL"[2] "USER"[3] "INST"Call UserCall Insttaller• You can store an adjusted audio setup value byselecting "MEMORY". Also, you can recall it byselecting "CALL". Refer to 'Audio Setup memory Recall'(page 32).3 Adjust the Audio setup itemPress the [4] or [¢] button.Each time the button is pressed the settingswitches as shown below.Adjustment Item RangeHigh Pass Filter FrontHigh Pass Filter RearHigh Pass Filter Center*3Through/30 — 250 (Hz)Low Pass Filter Subwoofer 30 — 250 (Hz)Subwoofer Phase setting Normal/ ReverseDTA Front/DTA Rear/DTA Subwoofer0 — 610 (cm)DTA Center*3 0 — 170 (cm)Bass Center Frequency 60 — 400 (Hz)Middle Center Frequency 500 (Hz) — 3.15 (KHz)Treble Center Frequency 4.00 (kHz) — 16.00 (KHz)Bass Level/ Middle Level/Treble Level-9 — +9 dBBass Q Factor/ Middle Q Factor/Treble Q Factor0.25/ 0.50/ 1.00/ 2.00SP-LEV Front Left/SP-LEV Front RightSP-LEV Rear Left/SP-LEV Rear RightSP-LEV Center*3/SP-LEV Subwoofer-10 — +10• The Adjustment item can also be controlled by therotary volume knob. Refer to 'Rotary Volume knoboperation mode select' (page 13).• To get the best sound, first set the "CABIN" and "SP-SEL" parameters using the 'Audio Setup (Easy mode)'(page 28). Refer to 'Notes on Sound ManagementSystem' (page 11).• *3 Function of the KDC-PSW9527• When the 'Dual Zone System' (page 24) is ON, each ofthe following setup is ignored.- "X'over"/ "EQ" / "DTA"4 Exit Audio setup modePress the [6] ("RTN") button.Audio Setup Memory (PRO mode)1 Selects the PRO mode of Audio setupSee the 'Audio Setup' (page 50) and select "AudioSetup: PRO".2 Select the source for adjustmentPress the [SRC] button.3 Select the key function sectionPress the [NEXT] button.Repeatedly press the button until "AD SET" isdisplayed above the [3] button.Refer to 'Notes on Multi-function Key System'(page 10).4 Enter Audio Setup modePress the [3] ("AD SET") button.5 Select the Adjustment item sectionPress the [NEXT] button.Repeatedly press the button until the desiredAdjustment item is displayed above the [2] — [5]button.6 Select the Audio Setup item for adjustmentPress the [2] — [5] button.Adjust the audio setup by referring to the 'AudioSetup (PRO mode)' (page 30).7 Select the Memory item sectionPress the [NEXT] button.Repeatedly press the button until "MEMORY" isdisplayed above the [2] button.8 Select the Memory itemPress the [2] ("MEMORY") button.9 Stores the adjusted audio setup value inmemoryPress the [2] ("USER")/ [3] ("INST") button forat least 2 seconds.The "MEMORY" display blinks 1 time."USER": The values are erased from memory if thebattery is removed or if the reset buttonis pressed."INST": The values are held in memory even if thebattery is removed or if the reset buttonis pressed.10 Exit Audio Setup modePress the [6] ("RTN") button.