Panasonic DMR-E60S Operating Instructions Manual

Also see for Diga DMR-E60: Firmware instructions Operating instructions Operating instructions

Contents

55RQT6981ReferenceError messagesOn the television PageOn the unit’s displayNo disc. ≥You haven’t inserted a disc. Correctly insert a disc that this unit can use.≥The disc is upside down. If it is a single-sided disc, insert it so the label is facing up.1014This is non-recordable disc. ≥The unit cannot record on the disc you inserted. Insert a DVD-RAM or unfinalized DVD-R.≥You inserted an unformatted DVD-RAM. Format the disc with this unit. 1038This disc is not formattedproperly.Please format the disc in ‘DISCSETTING’ to record.Cannot write into this card. ≥You cannot format a microdrive or mobile hard disk on this unit.This disc cannot be read. ≥You inserted an incompatible disc. 10Please check write protect tabon the disc.≥The write-protect tab on the cartridge is set to PROTECT.Use a ballpoint pen or similar to release the write protection.—Contents of this disc are pro-tected.≥The program is write-protected. Cancel the protection.≥The disc is write-protected. Cancel Disc Protection.3238Cannot finish recording com-pletely.≥The program was copy-guarded.≥No space left on the disc.‹ Create space by erasing any unwanted programs. [RAM]‹ Use a new disc. [RAM] [DVD-R]≥Recording was not completed for some other reason.—32——Cannot record on the disc. ≥The disc is scratched. Use another disc.≥The disc is dirty.≥You inserted an incompatible disc.—5410Disc is full. ≥No space left on the disc.‹ Create space by erasing any unwanted programs. [RAM]‹ Use a new disc. [RAM] [DVD-R]32—Please set clock. ≥The clock is not set. 47This disc may not be played inyour region.≥You tried to play a disc with a region number different from this unit’s region number. This unitcan only play discs with the region numbers compatible with this unit (1, All, or including thenumber 1).CoverpageYour selection exceeds therecorder’s rating limit.≥A ratings level has been set for DVD-Video with this unit. Unlock the unit with “Ratings” in“Disc”. 44Finalizing is necessary forcompatible playback.≥To enable playback of your DVD-R on compatible equipment, it is necessary to finalize it. 38No PC card.No valid PC card.No SD card.No valid SD card.≥The card is not inserted. If this message is displayed with a compatible card already inserted,turn off the power, remove and then re-insert the card.≥The card format does not match.≥The card inserted is not compatible.181111Please check write protect tab. ≥Release the protection on the card.≥Release the protection on the DVD-RAM.1110No folder ≥There is no compatible folder in this unit. 11Cannot write. ≥The card is currently protected ‹ Release the write protection.≥There is no space remaining. ‹ Erase any unwanted files (still pictures).1136Error has occurred. Pleasepress [ENTER].≥A serious, but temporary error has occurred and one of the unit’s safety devices has activated.Press [ENTER]. The unit switches to the standby mode. Press [Í, DVD POWER] to turn theunit on again.—PROTECTNO READ ≥The disc is dirty or badly scratched.‹ Clean the disc if it is dirty.‹ The disc cannot be played if it is scratched and this display doesn’t disappear.≥The unit cannot read the disc.≥You have used a DVD-RAM/PD lens cleaner and it has finished.54——58UNSUPPORT ≥You have inserted a disc the unit cannot play or record on. 11U14 ≥The unit is hot.‹ The unit switches to standby automatically for safety reasons and you cannot operate it.Wait for about 30 minutes for the service number to disappear.‹ Select a position with good ventilation when installing the unit.‹ Do not block the cooling fan on the rear of the unit.———U99 ≥The unit fails to operate properly. Press [Í, DVD POWER] to switch the unit to standby. Nowpress [Í, DVD POWER] again to turn the unit on. —CHK REMOTE ≥The remote control and main unit are using different codes. Change the code on the remotecontrol or main unit. 46RECOVER ≥There was a power failure or the AC plug was disconnected while the power was on. The unit iscarrying out its recovery process. Wait until the message disappears. —