Panasonic DMR-E60S Operating Instructions Manual

Also see for Diga DMR-E60: Firmware instructions Operating instructions Operating instructions

Contents

7RQT6981Setting upPreparation≥Confirm that the antenna is connected correctly.≥Turn on the television and select the appropriate video input tosuit the connections to this unit.1 Press [Í, DVD POWER] to turn theunit on.2 Press [3, 4] to select the menu lan-guage and press [ENTER].e.g., when you selectEnglish3 Press [ENTER].Plug-in Auto Tuning starts and the unit puts the stations itcan receive into channels.The unit then proceeds with Auto Clock Setting. The time isdisplayed when finished. If the clock is an hour slower orfaster than the actual time, go to “Time Zone Adjust” to cor-rect it (➜page 47).4 When the display shows the correct timePress [ENTER] to complete Plug-inAuto Tuning.If the unit couldn’t set the clock automaticallyPress [ENTER] to show the “Manual Clock Setting” screen. Set thetime manually (➜page 47).To start Plug-in Auto Tuning again (after reloca-tion, for example)When the unit is on and stopped1 Press and hold [X, CH] and [W, CH] on the main unit forabout five seconds.The unit turns off.2 Press [Í, DVD POWER] to turn the unit on.Follow the above steps 2–4.1 Press [SETUP] to show the menus.2 Press [3, 4] to select “Channel” andpress [1].3 Press [3, 4] to select “Antenna Sys-tem” and press [ENTER].4 Press [3, 4] to select “TV” or“CATV” and press [ENTER].The screen shown in step 2 reappears.5 Press [3, 4] to select “Auto ChannelSetting” and press [ENTER].If you have not yet set clock, the “Auto Channel/Clock Set-ting” screen appears.6 Press [ENTER].Auto setting starts. This takes a few minutes. (To stop autochannel setting, press [RETURN].) When finished, the Com-plete screen or time display is shown. Press [ENTER].To return to the previous screenPress [RETURN].When you are finishedPress [SETUP].Add or delete channels if necessary channels are not set or unnec-essary channels are set.While this unit is receiving the antenna signal (but not duringrecording):1 Press the numbered buttons to selecta channel.e.g., “5”: [0] ➜ [5]“15”: [1] ➜ [5]“115”: [100] ➜ [1] ➜ [5]≥You can also use [W, X, CH]when you are going to delete a channel.2 Press [ADD/DLT].The channel is deleted if it was set or added if it was not set.e.g.,Repeat steps 1 and 2 as necessary.Antenna system, channel caption, and VCR Plusr guidechannel settings all revert to the default values when youperform the procedure below. Timer recording settings arealso cleared.If Plug-in Auto Tuning failsEnglishEspañolFrançaisPress ENTERPulse ENTERAppuyer sur ENTERSelect LanguageSeleccione la LenguaSélection de LangueRETURNENTERAuto Channel/Clock SettingConnect antenna cable and if you use acable box, tune it to your local PBS CHthen. . .Please push the ENTER key.TAB SELECTAntenna SystemAuto Channel SettingChannel CaptionPreset Channel CaptionManual Channel CaptionVCR Plusi CH SettingCATVChannelSETUPRETURNSet UpDiscVideoAudioDisplayTV ScreenAdding and deleting channelsAntenna SystemAuto Channel SettingChannel CaptionPreset Channel CaptionManual Channel CaptionCATVSet UpDiscChannelSETUPSETUPSet UpChannelAntenna SystemTVCATVSETUPSet UpDiscVideoAudioDisplayChannelAuto Channel SettingConnect antenna cable and if you use acable box, tune it to your local PBS CHthen...Please push the ENTER key.Unit’s displayCHANNEL 15 DELETED