Parker COMPAX-M /-S (L) User Manual

Contents

Parker COMPAX-M /-S (L) User Manual Manual pdf 206 page image

Accessories and options COMPAX-M / -SHand-held terminal2069.8 Appendix: COMPAX componentsMains module for COMPAX-M (excluding COMPAX 35XXM)NMD10 Up to 3 x 500 V AC mains supply connection; direct mains supply operation 10 kW cont. outputNMD20 As NMD10, but with 20 kW continuous output; external ballast resistances available in 3 sizes.HDY and HJ motorsYou will find information about our range of motors in the motor documentation.Motor and resolver cable for HDY and HJ motorsYou will find motor and resolver cables on Page 46.HAUSER linear unit and initiator equipmentHLE 80mm / 100mm / 150mm edge length (ask for information material!)HPLA 80mm / 120mm / 180mm edge length (ask for information material!)Initiator equipment IVD1/. Initiator distr.connect. w. cables of the f. lengths [m]:2.5; 5; 7.5; 10; 12.5; 15; 20; 25; 30; 35; 40; 45; 50Initiator PNP induction proximity switch: IN HE 521 506 with 6m cable.AccessoriesBDF2/01 Hand-held terminal for configuring and operating COMPAXBDF1/03 External control panel with housing and without cableBDF1/02 External control panel for front plate installation without cableSSK6/.. Interface cable between contr. panel and COMPAX av.- in the following lengths: 2.5; 5; 7.5; 10; 12.5; in [m]SSU1/01 RS232 - RS485 converters used in conjunction with option F1GBK16 COMPAX ñ motor cable for disposing of SinCos.Encoder: GBK11/.. Encoder cable for connecting COMPAX with an encoder.EAM4/01 Encoder distributor for creating an encoder bus. BUS1/01 Bus termination for encoder busSSK4/.. Connector cable between COMPAX and encoder distributor.SSK7/.. Connector cable between encoder distributors or from an encoder emulation.ASS1/01 Monitor box for outputting internal measurement signals with D1 option.SSK1/.. RS 232 Interface cable for PC COMPAX, available in the following lengths: 2.5; 5; 7.5; 10; in [m]Ballast resistors NMD20: BRM4: 0.57 kW-1.5 kW (15Ω) COMPAX 25XXS: BRM5/01: 250W (56Ω)COMPAX 45XXS/85XXS: BRM6/01: 450W (22Ω) COMPAX 35XXM: BRM7/01: 2 kW (10Ω)COMPAX 1000SL BRM8/01: 60W (100Ω)AC power filter NMD10 / COMPAX 45XXS/85XXS: NFI01/02 COMPAX 25XXS: NFI01/01 or NFI01/06 (≤ 10m motor cable)COMPAX 35XXM: NFI01/04 or NFI01/05 (with additional COMPAX-M) NMD20: NFI01/03COMPAX 1000SL: NFI01/01 (<50m motor cable) or NFI01/02 (>50m motor cable)Motor outp. throttle For motor lines >20m: MDR01/01 (16A/2mH) • MDR01/02 (30A/1.1mH) • MDR01/03 (>30A/0.64mH)Ass. angle bracket: MTS2: for indirect wall installation (heat sink in separate heat chamber) of COMPAX 02/05/15XXMFan set for NMD Fan set for NMD10 and NMD20 to increase max. brake performanceServoManager To read and write COMPAX parameters and programsBus terminal BUS1/01: Encoder bus BUS2/01: HEDA BUS3/01: ProfibusBUS4/01: RS485 BUS6/01: Encoder terminal for COMPAX 1000SLOptionsF1 4-wire RS485 interface F5 2-wire RS485 interfaceF2 Interbus S interface F3 Profibus F7 CS31 F8 CANopen F4 CANbusE2 Encoder interface with line terminator for individual connections.E3 Encoder simulation for resolverE4 Encoder interface without line terminator for creating an encoder bus.E7 Analogue speed specification only for COMPAX XX6X and COMPAX XX70 or for SPEED SYNC with COMPAX XX00!A1 Absolute value sensor/HEDA Cable to COMPAX: GBK1/.. lengths: 2.5; 5; 7.5; 10; 12.5; 15; 20; 25; 30; 35; 40; 45; 50 [m]A4 HEDA f. COMPAX 1000SL Cable COMPAX/COMPAX: SSK14/.. lengths :2.5; 5; 7.5; 10; 12.5; 15; 20; 25; 30; 35; 40; 45; 50 [m]D1 D/A monitor To output the measurement signals, you will need monitor box ASS1/01.S1 Sensor interface for SinCos, single-turn or multi-turn S2 Programmable sensor interface for SinCos multi-turnS3 Sensorñinterface for linear motors (cable: GBK18)