Regency City CV60E-1 Owners & Installation Manual

Also see for City CV60E-1: Owners & installation manual

owner's information24 | City Series CV60E-1City Series CBV0E | 19owner's informationInner Glass Panel Installation / Removal1. Remove outer safety barrier glass panels if previously installed–see instruc -tions in this manual.2. Remove outer panels installed in unit - see panel removal section in this manual.3. From the front inside lower panel of the unit--pivot the glass support intoupright position as shown below.WARNING: GLASS HANDLINGWe recommend using the glass vacuum holders supplied by the manufac -turer. Lower the glass to rest in a safe place, this is to prevent damage to theglass edges. Extra care must be taken when removing/installing the glass.Breakage or damage to the edge of the glass which occurs as a result ofcareless handling will not be covered under warranty.• We recommend handling the glass with supplied vacuum clamps• When removing glass–prepare a soft, scratch resistantsurface to place the 60-3/8"x 18-1/4" glass• Never clean or remove hot glassNote: The suction cups may leave a round film on the glass whenused. Ensure that the glass is cleaned using a fireplace glasscleaner after each removal and prior to operating the appliance.Note: glass panels must be installed to operate fireplace4. Open the 8 clamps at the top of the glass.Handle glass with supplied vacuum clampsGlass supports in upright positionClamps in closed positionWith the top clamps in open position, use your hands to pull the two glassgasket rails towards you.Clamps in open position, rail pulledforwardPress glass vacuum clamps in open position firmly onto surface of glass.Bring handles together to close.Open ClosedNote--the following installation diagrams do not include the vacuumclamps but it is strongly recommended to use clamps atall times when handling the firebox glass.Glass removal videoInner Glass Panel Installation / Removal1. Remove outer safety barrier glass panels if previously installed–see instruc-tions in this manual.2. Remove outer panels installed in unit - see panel removal section in this manual.3. From the front inside lower panel of the unit--pivot the glass support intoupright position as shown below.WARNING: GLASS HANDLINGWe recommend using the glass vacuum holders supplied by the manu-facturer. Extra care must be taken when removing/installing the glass.Rest the glass in a safe place to prevent damage to its edges. Breakageor damage to the edge of the glass resulting from careless handling is notcovered under warranty.• We recommend handling the glass with the suppliedvacuum clamps.• When removing the 60-1/4"x 19-13/16" glass, pre-pare a soft, scratch-resistant surface to place it on.• Never clean or remove hot glass.Note: The suction cups may leave a round film on the glass.Clean the glass using a fireplace glass cleaner aftereach removal, prior to operating the appliance.Note: glass panels must be installed to operate fireplaceCity Series CBV0E | 19owner's informationInner Glass Panel Installation / Removal1. Remove outer safety barrier glass panels if previously installed–see instruc -tions in this manual.2. Remove outer panels installed in unit - see panel removal section in this manual.3. From the front inside lower panel of the unit--pivot the glass support intoupright position as shown below.WARNING: GLASS HANDLINGWe recommend using the glass vacuum holders supplied by the manufac -turer. Lower the glass to rest in a safe place, this is to prevent damage to theglass edges. Extra care must be taken when removing/installing the glass.Breakage or damage to the edge of the glass which occurs as a result ofcareless handling will not be covered under warranty.• We recommend handling the glass with supplied vacuum clamps• When removing glass–prepare a soft, scratch resistantsurface to place the 60-3/8"x 18-1/4" glass• Never clean or remove hot glassNote: The suction cups may leave a round film on the glass whenused. Ensure that the glass is cleaned using a fireplace glasscleaner after each removal and prior to operating the appliance.Note: glass panels must be installed to operate fireplace4. Open the 8 clamps at the top of the glass.Handle glass with supplied vacuum clampsGlass supports in upright positionClamps in closed positionWith the top clamps in open position, use your hands to pull the two glassgasket rails towards you.Clamps in open position, rail pulledforwardPress glass vacuum clamps in open position firmly onto surface of glass.Bring handles together to close.Open ClosedNote--the following installation diagrams do not include the vacuumclamps but it is strongly recommended to use clamps atall times when handling the firebox glass.Glass removal video4. Open the 8 clamps at the top of the glass.Handle glass with supplied vacuum clampsGlass supports in upright positionClamps in closed positionWith the top clamps in open position, use your hands to pull the two glassgasket rails towards you.Clamps in open position, rail pulledforwardPress glass vacuum clamps in open position firmly onto surface of glass.Bring handles together to close.Open ClosedNote--the following installation diagrams do not include thevacuum clamps but it is strongly recommended to useclamps at all times when handling the firebox glass.Glass removal video