Regency City CV60E-1 Owners & Installation Manual

Also see for City CV60E-1: Owners & installation manual

74 ............................................. |City Series CV60E-1installation74 | City Series CV60E-1LP Conversion Instructions920-225 06.09.201CITY SERIES 60CONVERSION FROM NG TO LPCV60E using SIT 885 NOVA Gas ValveCaution: The gas supply shall be shut off prior to disconnecting theelectrical power, before proceeding with the conversion.Always let the appliance cool to room temperature before servicing.1 Remove the outer panels and safety glass — see manual.2. Remove inner firebox glass — see manual.3. Remove inner panels — see manual.4. Remove all media installed on burner (glass, logs or stones, etc).5. Lift off the far right base panel and loosen 2 screws on IFC cover--re-moved cover to access IFC.6. Disconnect the Cable coming from the Pressure Regulator Motor.WARNINGThis conversion kit shall be installed by a qualified ser-vice agency in accordance with the manufacturer’s in-structions and all applicable codes and requirementsof the authority having jurisdiction. If these instructionsis not followed exactly, a fire, explosion or productionof carbon monoxide may result causing property dam-age, personal injury or loss of life. The qualified serviceagency is responsible for the proper installation of thiskit. The installation is not proper and complete untilthe operation of the converted appliance is checked asspecified in the manufacturer’s instructions suppliedwith the kit.THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTERIF IN DOUBT DO NOT DO THIS CONVERSION!Cable from motorConversion Kit 686-969 includes:1 911-191 Stepper Motor LP for 885 SIT1 905-046 Orifice #501 910-037 Pilot Orifice #301 918-590 Decal - Conversion to LP1 908-528 Label Propane1 904-529 5/32" long Allen Key1 920-225 Instruction Sheet7. Remove and discard 2 Pressure regulator screws (A)using a (T20 or slotscrewdriver,) Pressure Regulator (B) and Spring and Diaphragm (C)(see below).8. Ensure the rubber gasket, which is prefitted as part of the Assembly,is properly positioned. Install the new Pressure Regulator using the 2xM4 x .7 screws supplied. Tighten the screws to 25lb-in. In the event thatthe screw threads are cross threaded or stripped, replace the valve as-sembly.Install the enclosed propane identification label to the valve body where itcan be easily seen.Pressureregulatorscrews9. Re-attach the Pressure Regulator wire (disconnected in Step 6), and re-situate the IFC, secure the screws that fasten the IFC Mounting Brackets.10. Remove pilot hood by lifting up and off.tooltipCity Series CBV0E | 59installationLP Conversion Instructions920-179 10.31.191CITY SERIES 60CONVERSION FROM NG TO LPCB60E using SIT 885 NOVA Gas ValveCaution:The gas supply shall be shut off prior to disconnecting theelectrical power, before proceeding with the conversion.Always let the appliance cool to room temperature before servicing.1 Remove the outer panels and safety glass — see manual.2. Removeinner glass — see manual.3. Remove inner panels — see manual.4. Removeall media installed on burner (glass, logs or stones, etc).5. Lift off the far right base panel and loosen 2 screws on IFC cover--re -moved cover to access IFC.6. Disconnect the Cable coming from the Pressure Regulator Motor.WARNINGThis conversion kit shall be installed by a qualified ser -vice agency in accordance with the manufacturer’s in -structions and all applicable codes and requirementsof the authority having jurisdiction. If these instructionsis not followed exactly, a fire, explosion or productionof carbon monoxide may result causing property dam -age, personal injury or loss of life.The qualified serviceagency is responsible for the proper installation of thiskit. The installation is not proper and complete untilthe operation of the converted appliance is checked asspecified in the manufacturer’s instructions suppliedwith the kit.THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTERIF IN DOUBT DO NOT DO THIS CONVERSION!Cable from motorConversion Kit 686-969 includes:1 911-191 Stepper Motor LP for 885 SIT1 905-046 Orifice #501 910-037 Pilot Orifice #301 918-590 Decal - Conversion to LP1 908-528 Label Propane1 904-529 5/32" long Allen Key1 920-179 Instruction Sheet7. Remove and discard 2 Pressure regulator screws (A)using a (T20 or slotscrewdriver,) Pressure Regulator (B) and Spring and Diaphragm (C)(see below).8. Ensure the rubber gasket, which is prefitted as part of the Assembly,is properly positioned. Install the new Pressure Regulator using the 2xM4 x .7 screws supplied. Tighten the screws to 25lb-in. In the event thatthe screw threads are cross threaded or stripped, replace the valve as -sembly.Install the enclosed propane identification label to the valve body where itcan be easily seen.Pressureregulatorscrews9. Re-attach the Pressure Regulator wire (disconnected in Step 6), and re-situate the IFC, secure the screws that fasten the IFC Mounting Brackets.10. Remove pilot hood by lifting up and off.tooltip11. Remove the trim cover on right side of burner by lifting off. Also removethe burner surround by sliding to the left and lifting off.Trim cover Burner SurroundPilot hoodBase PanelIFC cover 11. Remove the trim cover on right side of burner by lifting off. Also removethe burner surround by sliding to the left and lifting off.Trim cover Burner SurroundPilot hoodCV60E shown